My first day with a Kayfun Lite - impressions
- Thread starter bobrob
- Start date
- th_trl_thread_readers 0
- Status
i've noticed that anything under .8ohm will not work at all but a .96ohm works really well in a nano or micro coil
I've never vaped a Kayfun before today. And I'm very embarrassed to ask this question but I just built my Ehpro Kayfun clone for the first time and everything went well (1.9 Ohm) but now I'm having a devil of a time trying to figure out how to fill the metal tank.
Does the part just below the drip tip screw off from the first large piece of metal where there looks to be a seam? If so, I can't get it to come apart. It is vaping well from just the juice I put on the coil but when I try to fill the tank, it's leaking out all over everything, from the airhole I believe. Anyway, I put just a little juice into the side of the first part that I could get apart and didn't get juice in the chimney hole but it's all leaking out when I try to vape. I'm obviously dumping the juice in the wrong place. What am I doing wrong?
Does the part just below the drip tip screw off from the first large piece of metal where there looks to be a seam? If so, I can't get it to come apart. It is vaping well from just the juice I put on the coil but when I try to fill the tank, it's leaking out all over everything, from the airhole I believe. Anyway, I put just a little juice into the side of the first part that I could get apart and didn't get juice in the chimney hole but it's all leaking out when I try to vape. I'm obviously dumping the juice in the wrong place. What am I doing wrong?
Last edited:
Remove the phillips screw from the bottom of the tank. Pour the juice in there! It fills from the bottom, not the top.
Make sure the tank is assembled before you do that. There is a little screwdriver with a key ring in your case (probably)
Make sure the tank is assembled before you do that. There is a little screwdriver with a key ring in your case (probably)
I'm not even going to tell you that....ah geeeezzz. I forgot to put that screw back in the bottom. Well, I sure stand corrected. I don't like the idea of unscrewing screws to fill a tank. That didn't even cross my mind when I bought it. Live and learn. Thanks for your help! 
Don't feel bad.. the first time I tried to use an Ego (in a shop no less), my first question was "What is that button for?" That button was the fire button. All my stick batteries before that were automatics. I had never heard of a "manual" battery before.
And by the way, the part that the drip tip fits into does come apart from the rest of the tank. Mine was super-tight when I first got it, and I also wondered if it came off. I finally got it unscrewed though.
I've done .7 & .8 double barrels before and even though it's a great vape, it can get too hot. Around .9-1 is the sweet spot for me on double barrels, but I usually run singles between 1 and 1.6, depending on the wire that I'm using or what juice I want to fill the tank with.
my ehpro 3.1 kayfun no longer allows me to take off the 510 ring and give me access to the bottom screw :/ anyone have a fix for this? it seems like it just got screwed on wayyy too tight.. and the side fill sucks worse than molasses in a coffee stir straw!! and im using 50/50 juice
I dunno why but the more i read about kayfun the more i want it....whats worse is that its not easy get stuff to a country where evrything to do with vaping is banned
Sent from The Slaughtered Calf Inn using a brick
Sent from The Slaughtered Calf Inn using a brick
Even if I go and get it going back into my country is not easy..border security is also clamping down hard on smugglers..
Sent from The Slaughtered Calf Inn using a brick
Sent from The Slaughtered Calf Inn using a brick
Where the heck do you live?? Behind the Berlin Wall?! Try to put it in a vase hahaha
I have two Russians, one of them whistled last week but stopped without me making any adjustment.
Glad to hear more good news about the Kayfun. I ordered my Kayfun Lite Plus (second batch) last week. Can't wait for it to arrive.
- Status
Similar threads
