Nebraska Vaping, Part 2

[PittBoss]

Ah...love you too pookies.

Lol...know what I just remembered? When they were speaking at the reception and told Pitt he was one of the girls
You think Jen brought up the knife and lacquer thinner like you suggested?

I'm sorry if you are put off by the fact that I am a ladies man..lol

 

[Jakersvape]

make sure your coils are wrapped properly on the terminals and also check to make sure that the positive pin is making contact with your PVs connector. You ay need to pull that pin down or something

I think it's the positive pin....and I don't believe it can be pulled down.....I think most of the problem is that it won't screw down all the way on the zmax for some reason.... It will screw all the way on my inferno.....

 

[PittBoss]

So I think the center post on my igo-l doesn't stick out far enough on the bottom to make contact with the center plate of my zmax....and best I can tell, it's not adjustable like the aga....

That is my first guess.. You can adjust it with a precision flat-head or even a paper clip

 

[Jakersvape]

I just pretty much read quickly through 32 pages of posts on an igo-l thread and only one mention about the center pin not making contact on a Provari....
Pitt, you are definitely gonna have to look at this tomorrow!

 

[PittBoss]

Its going out tomorrow when i mail off my bad pv also... do i need to say anything special about it when i mail it? never actually mailed nic juice before

I never do and I haven't had any issues

 

[PittBoss]

Hahaha.....I forgot about that....that was classic....since I'm trying my best to be nice, and I might need his help for a few minutes with this igo-l when I take him cookies tomorrow, I'll just leave it at that....for now

I wanna hear em! I promise I won't get upset like Hawk does

 

[Jakersvape]

That is my first guess.. You can adjust it with a precision flat-head or even a paper clip

I can't really even get under the pin with anything I've got

 

[PittBoss]

Nope....I don't think it is screwing all the way down....look at this gap...

Now here is one with the aga on....the posts are pretty much the same length...

Yeah.. That's not going to be making contact on that ZMax.. That gap is atrocious!

 

[PittBoss]

ya its going in a priority box with a bunch of other stuff so i might just fib or something lol.. dunno how that works

If you get the label from the station or take it up to the counter, they ask you if their is anything liquid or hazardous.. I always say no and it's a done deal

 

[Jakersvape]

I wanna hear em! I promise I won't get upset like Hawk does

I sometimes forget how sensitive he is....

I admire that your a ladies man, and now I see why you weren't too worried about the lacquer, rusty knife and plexiglass box....

I'm just kidding....love you, brother!

 

[PittBoss]

I screwed them both on an inferno, and they both sit pretty flush, the igo-l sits a hair higher. Neither will fire on the inferno...not quite sure why the aga won't fire...it's at 1.8ohms, so it shouldn't be too low for the inferno.

Of course I wiggled my finger in it while holding my tongue!

What mah is the Inferno battery? They might even have protection for anything under 2 ohms

 

[PittBoss]

I just pretty much read quickly through 32 pages of posts on an igo-l thread and only one mention about the center pin not making contact on a Provari....
Pitt, you are definitely gonna have to look at this tomorrow!

Yay, I get to look at yours!

 

[PittBoss]

I can't really even get under the pin with anything I've got

Well, I don't think it's gonna matter if it doesn't even screw in all the way

 

[Jakersvape]

Yeah.. That's not going to be making contact on that ZMax.. That gap is atrocious!

I can't see why it's not screwing all the way down, the posts are pretty much the same length, and the threads don't look messed up.....damn....another typical "jake gets an rba and can't figure it out, dumbass!"

 

[Jakersvape]

What mah is the Inferno battery? They might even have protection for anything under 2 ohms

Umm....I think the one I tried it on was 600mah, I have a 900mah one too. I was thinking they sell low res attys for them that are around 1.5ohms

 

[Jakersvape]

Yay, I get to look at yours!

I'll show you mine if you show me yours....gotta warn ya though, I don't have 3 like Leia does......lol

 

[Jakersvape]

Well, I don't think it's gonna matter if it doesn't even screw in all the way

I think I would have to agree with you

 

[PittBoss]

I sometimes forget how sensitive he is....

I admire that your a ladies man, and now I see why you weren't too worried about the lacquer, rusty knife and plexiglass box....

I'm just kidding....love you, brother!

Lol.. I have one word for you, buddy.. Magnum, lol. You guys are having a lot of fun with this castration talk, aren't ya? I think it's cute.

 

[hawkizefan]

I'm sorry if you are put off by the fact that I am a ladies man..lol

No man...I dig it. Just gave Jake and I something to tee-hee about.
You almost got a here, here HARUMPH at one point.

 

[PittBoss]

I can't see why it's not screwing all the way down, the posts are pretty much the same length, and the threads don't look messed up.....damn....another typical "jake gets an rba and can't figure it out, dumbass!"

I dunno.. I have never had anything of this sort that hasn't sat down all the way. I am baffled.. The only thing I can think of, is the thread pitch on the atty