Need help with iclear30

[Twendt]

I purchased the mvp v2 a few weeks ago. It came with the iclear30 tank/clearomiser. Over all its alright.

My issue is with the iclear leaking into the 510 connection and the coil doesn't seal completely with the drip tip, if you look dead on you can tell the center shaft is crooked, and the rubber cap doesn't seal completely against the bottom of the drip tip.

Before you ask, yes the coil is screwed on the base flush and the o ring isn't damaged or not sitting on the base correctly, I've tried 2 different coil head so far they both do the same thing. I personally think the problem is with the base. I've included a few pics to try and show what I'm talking about. Going back to vape shop again tomorrow to see what they say again. I do not think this is normal.Thanks and I hope with some help I can get it resolved.

Sent from my SM-N900T using Tapatalk

 

[Twendt]

You can see in the last picture the cap isn't even with the drip tip. If anyone wants me to get another pic I can do my best

Sent from my SM-N900T using Tapatalk

 

[Twendt]

If this is the wrong section, mods please move Thank you

Sent from my SM-N900T using Tapatalk

 

[DreamWithin]

Moved to Clearomizers forum

 

[Twendt]

Thank you

Sent from my SM-N900T using Tapatalk

 

[CastleRat]

I had the same problem with one of mine. I took the top and center piece off and pushed it to straighten it. It took me two tries - fine since then.

 

[Twendt]

Hmmmmm so you pushed the coil head to straighten the base?

Sent from my SM-N900T using Tapatalk

 

[CastleRat]

I had mine mounted on a itaste 134 to make it solid. I think the stem coming up from the base on mine was off a little. Pushing just under the lower coil gives a little leverage to move it over. It doesn't have to move much just a tiny bit. I had to reassemble mine each time to see if it moved.

 

[Twendt]

I'll give it a try, hoping the vape shop manager will exchange it for me as it only 2.5 weeks old. It doesn't sit square on my MVP2 either . He w as set there today and the employee didn't have the power to do an exchange, but he did note that it's not normal.

Sent from my SM-N900T using Tapatalk

 

[CastleRat]

I just checked a new unopened one I had for a spare. It was off exactly like yours. I tried pushing it and this time it didn't work. I removed the coil head and checked the seal - it was ok. I reinstalled the coil head and this time it was off by a tiny sliver. I removed the mouth piece and tilted the cap and put the mouth piece back on - perfect! I hope that works for you.

 

[CastleRat]

Congratulations! I'm sure you haven't been rude by not responding, so you have fixed the problem yourself. The Iclear 30 is the best of the clearomizers on the market. Enjoy!

 

[Twendt]

Sorry man I worked all day lol yes I took it in to the shop, and the manager couldn't exchange it but he was able to tweak it like you said to try and it's alot better now. Coil is straight and no more leaking

Sent from my SM-N900T using Tapatalk

 

[Twendt]

Now I'm getting burnt taste every hit Hmmmmm I guess I'll try and clean every thing real good and dry burn this coil or switch to one of the other spares I have

Sent from my SM-N900T using Tapatalk

 

[PaulBHC]

Just to be sure, your MVP can either use watts or volts, not both. Which ever button you press last is the one it uses. Press the P and hold it till you see first the puff count and then the watts. It should be 7.0 to 9.0 depending on your juice.

 

[Twendt]

I never leave watts. I think it is the juice I have currently it's from a local owned and operated shop and it's I don't think the best quality. No Clue Of THE pg/vg Ratio either.

Sent from my SM-N900T using Tapatalk