new v1.1
- Thread starter slowintegra
- Start date
- th_trl_thread_readers 0
- Status
yea it vapes but man.... serious??????
for real! not sure what your post is about (the gap?) i think it was intentional so it could accommodate non joye 510's? someone else here will know for sure.
Hmm. That's not good. I hope the SS 510 adapters for Prodigy V2 won't have that kind of gap...
Guys, our 510 adapters are always going to have a gap. We had to lengthen the center posts on all 510 adapters so they would work with different 510 attys.
You could use a small rubber o-ring like on so many of the other adapters...
With all the manufacturers making different / non consistent attys I think it's fitting.
If they made it to fit flush there would be people posting about it not making contact with the attys they get from x or y.
Hard to please eveyone at once...
With all the manufacturers making different / non consistent attys I think it's fitting.
If they made it to fit flush there would be people posting about it not making contact with the attys they get from x or y.
Hard to please eveyone at once...
The gap is not the problem. We know that the gap is necessary for the 510 to function correctly. The problem is that the flange surrounding the connection doesn't come far up enough to mask the gap, as it does in the current brass center adapters. Having the gap exposed like that makes the device look unfinished. I'm very surprised Puresmoker would find that acceptable. It's a case of bad design IMO.
I'd hate buy one of these and then find that PS was releasing one with a higher flange and have to buy yet another adapter for this thing. Frankly, seeing that image makes me VERY suspect about sticking with the V2 Prodigy at all. If the gap is exposed like that, I think I may have to find another mod. That unfinished look simply isn't acceptable.
I'd hate buy one of these and then find that PS was releasing one with a higher flange and have to buy yet another adapter for this thing. Frankly, seeing that image makes me VERY suspect about sticking with the V2 Prodigy at all. If the gap is exposed like that, I think I may have to find another mod. That unfinished look simply isn't acceptable.
Last edited:
I didn't realize it didn't have a well..
I agree. Poor design..
I hate to say but I've already moved away from the V2.
Love the people and the company but the latest designs are lacking in innovation and forward thinking..
I have my original V1 Prodigy and Protege that are still absolute workhorses but these lateset pieces just don't do it for me..
I agree. Poor design..
I hate to say but I've already moved away from the V2.
Love the people and the company but the latest designs are lacking in innovation and forward thinking..
I have my original V1 Prodigy and Protege that are still absolute workhorses but these lateset pieces just don't do it for me..
the no well thing does kind if suck. I tend to overdrip sometimes (we prob all do) and it ends up leaking on to the outside of the adapter... didn't have that issue with my protege v1.
yup i dont mind the gap i wish they would have made it // | | \\ to cover the gap.
I like the new adapter, (v1.1) its easier to clean the top of it.
Personally I don't have any liquid overfilling issue much.. if at all.
If I do I'll just wipe it off with a cloth or my shirt.
But i do see how the liquid well might help.
Just my opinion though.
The well isn't so much to hold the overflow of liquid as it is to hide the gap on the different attys.
With the top being cut from a single piece it makes it almost immpossible to have a deep well around it.
I was pretty disappointed with the gap when I received it. Since then I've gotten used to it and don't think about (unless I read this post) because it sets off an OCD trigger inside me!
Is it no longer possible to adjust the center post? If all your atomizers are coming from the same source you should be able to adjust for the gap. You could on the brass adapters.
I was thinking the same thing. I cut center post height on my V1. Still vapes great and doesn't look funky.
- Status
