Yea I'm sure it's a picture of a real one. I've seen them have other stuff before way way under priced but out of stock. I think they do it to get traffic from sites like Vapecrawler kind of an electronic bait and switch.
NEW YIHI SX MINI ML CLASS!
- Thread starter smokyribs
- Start date
- th_trl_thread_readers 0
- Status
Yea I'm sure it's a picture of a real one. I've seen them have other stuff before way way under priced but out of stock. I think they do it to get traffic from sites like Vapecrawler kind of an electronic bait and switch.
I wondered if they did that to get site traffic too. They're conveniently out of stock of them. I imagine the price will change once they have them in stock.
Hi guys, I just bought a Black on Black SX Mini ML. I will be doing the update tonight to upgrade the firmware and play around. I was wondering about something I have been experiencing. On my Vapor Shark dna 200 I use a Crown .5 coil at 45 Watts, I get a nice steady hit all the way through. Same tank, same wattage, same coil, but adding "Powerful" which is why I bought this, it will begin nice and warm and cool off significantly after about 3 seconds. It's not in TC mode. Is there a setting I need to look at, or perhaps the firmware upgrade would fix this? Curious of others experience?
Thanks in advance.
Sent from my iPhone using Tapatalk
Thanks in advance.
Sent from my iPhone using Tapatalk
What Powerful does is add more wattage for the first second or so for a faster ramp-up (in your particular case, it fires at almost 50w), then it drops back down to your set wattage. What you could do is increase the base wattage to somewhere around 48-50w, and run it in Standard so it's a steady supply of power for the entire puff.
And just to point out the obvious, "Soft" is the opposite of Powerful, it runs reduced wattage for the first second or so then increases to your set wattage.
Will get time to play Sunday hopefully mate
Just posted on FB by Yihi! I just started a new thread on it.
SXmini Q Class Powered by YiHi SX450 chip
Oh there we go ... Just as my ML arrives
Aint even got time to play with this yet & am drooling over my next purchase
I put two in the cup holder together
Serves dual purpose, no bouncing about and they keep each other company when not in use
These authentic Yihi sleeves do look pretty nice but when will they be available?
Found out today the ML is a perfect fit in my Valentino M Class Bag
Good chance the M class sleeves will fit the ML ok
Similar to what Croak suggested, Powerful will apply about 10% additional power of your setting for the first 2 seconds then it will drop to your selected Power setting. Powerful+ will give you about 15%. We do appear to have inherited a previous bug where when in Temp mode those Presets don't work quite correctly and are under powered.
Edie: additionally once you do the update you could go into the SXI-Q software and configure the output curve that you like for up to 10 seconds I believe.
Last edited:
Anyone else has a large gap between the mod and the screen??
I can stick my finger nail between the screen and the main body.
I can stick my finger nail between the screen and the main body.
Last edited:
Nope, I can see a slight gap around the screen probably less than half a mm. I believe the screens attached to the pcb then attached to the chassis so if you can put your finger in between it you probably have something loose or really tiny fingers.
Nope, I can see a slight gap around the screen probably less than half a mm. I believe the screens attached to the pcb then attached to the chassis so if you can put your finger in between it you probably have something loose or really tiny fingers.
Sorry, ment to say finger nail.
Edited my post.
Thanks.
Decided to look at the SXI-Q curves a little bit tonight. Top image is of the SXI-Q power curve I set up and the bottom is the voltage output from that curve on my cheapo scope. Looks like a pretty good representation in general.
Pbusardo ML malfunctioned on him after a weeks time and apparently right as he was about to put up a review. Hopefully an isolated case and we don't start hearing of problems. He said the numbers were really good and it was destined for a thumbs up until it malfunctioned in his comments. Also said the charts and such are on TYJ for those interested.
Hopefully an isolated case and we don't start hearing of problems. He said the numbers were really good and it was destined for a thumbs up until it malfunctioned in his comments. Also said the charts and such are on TYJ for those interested.
fast forward to about the 2:53 minute mark for start of ML discussion....published today by Pbusardo...
Last edited:
Just got SS430 wire, made a coil out of 28g 4strands twisted. ID 3.2, 0.22 ohms.
TC settings. TCR 0.00138, 460F, 45j. Good warmish Vape on a Wotofo Serpent.
In pure power mode, ss430 wire spits juice even at low 25w.
TC settings. TCR 0.00138, 460F, 45j. Good warmish Vape on a Wotofo Serpent.
In pure power mode, ss430 wire spits juice even at low 25w.
Last edited:
- Status
Similar threads
- Locked
