NEW YIHI SX MINI ML CLASS!

[Wingsfan0310]

I see the Bellus has a plug so you can run single coils also. That's nice. Does it work well.

I think over all I would give the nod to the Billow V2. The Bellus has a slightly smaller build deck and can be a little more challenging. My first couple of builds leaked a bit. Then I my next build, I just packed the juice channels all the way to the base of the deck with cotton. No leaking since that. When it's right it may be just a tad better than the Billow, but if I only could have 1 it would probably be the Billow. I tend to use my Billows a touch more for what it's worth.

I've packed in as much as 11 wraps of Ni200 into the Billow V2 (that was a little tight but I needed to because of Ni200's ultra low resistance). Seven wraps (spaced) is a piece of cake. That's my normal build for 430 SS.

Cheers,
Steve

 

[2legsshrt]

Thanks STeve

 

[Wingsfan0310]

Thanks STeve

Your welcome my friend. Hope some of it was helpful.

Cheers,
Steve

 

[Quantum Mech]

How many wraps can you get on each side of the Billow with 24awg Ti.

5 slightly spaced mate

or 6 of the regular 26awg

Its a little belter of a tank, but am sure your luv the Bachelor too

 

[2legsshrt]

Yeah that coil in the Bachelor looks pretty tight. Had a laugh today watch Busardo's review of the new Kayfun Mini v3. He didn't get a big puff but he was vaping it on a VTVmini in Ti mode with a 5 wrap Sweet Spot vapes Ti at 75W 410F on Ti mode said it tasted real good to him.

 

[Quantum Mech]

Yeah that coil in the Bachelor looks pretty tight. .

That's 12 wraps of 24awg mate

Roughly the same as I get in a billow v2 but just all in one coil

 

[Vlad1]

Authentic Yihi sleeve came in from that Ebay seller today. Very nice fit, kind of tight putting on but not complaining about that would much rather it be tight than loose. These are really nice sleeves IMO if your in the market for one.

 

[ShowerHead]

Authentic Yihi sleeve came in from that Ebay seller today. Very nice fit, kind of tight putting on but not complaining about that would much rather it be tight than loose. These are really nice sleeves IMO if your in the market for one.

Mine arrived from VapinArt yesterday and they couldn't be nicer.
Excellent fit, not sticky, easy access to the hateful battery cap.
I like how they come up on the 510 connector, looks great.

 

[Moto-EC]

Ok, I created a shared Google Drive folder and placed the 2 v2.206 sxi files in there. One for the SXML and the other one is for the modders with the SX350J-2 chipset.

Yihi v2.206 Firmware

Someone please verify that you can access and download the files.

That worked for me! Thank you very much! I had tried to upgrade over the Chinese holiday and since then when I opened SXi-Q it told me to upgrade. I couldn't adjust anything and have it save. It was telling me I needed 2.205, I have never seen that anywhere. Now its all good!

 

[2legsshrt]

Well this Temco Ti other then the fact it looks different then any other Ti I have ever used is by far the cleanest. Now that I have my 6 wrap broken in it is really vaping good. I am trying the 24awg .19ohms. It is really sturdy and fairly soft when you bend it it holds the bend perfectly. It is not shiny in fact way duller then Unkamen and kind of a whitish grey in color. No signs of any graphite when wiped IPA. Using it was amazingly easy even getting 6 wraps of 24awg on the STM. Good vapor and other then it had a little bit of a strange taste at the very first is tasting very good now. I would definately recommend giving it a try. It is not as rogh as Unkamen but very dull in color. Not sure what processes they use but I really like it so far am going to try the 26awg next. The 24 was a little hard to place with the STM because of the diameter but got it in and was easy to keep the legs from touching the coil because of the way it holds position.

 

[2legsshrt]

This is my first 24awg coil and it went pretty well I thought. Think I will order a couple of Bachelors. They look way easy to build and can probably easily get a 24awg 7 wrap 3.5mm spaced coil Ti of course on it. Oh and the resistance is right on what SE says it should be. The best I have used so far. Don't know how they are making it but it is a new Ti. Don't know how it will clean up using the method I use which is hot tap water and a brush but it is very smooth just dull in color.

 

[2legsshrt]

Hey Mech if you are lurking I see that efun has those for 20 bucks but they are out. Fastech is 23 and eciggity is 24.99. For $1 I could get it in 3 days instead of 3 weeks but if efun had them I might go for that.

 

[2legsshrt]

I would need to spend 2 cents extra at eciggity to get 2 of them free shipping.

 

[JimScotty0]

This is my first 24awg coil and it went pretty well I thought. Think I will order a couple of Bachelors. They look way easy to build and can probably easily get a 24awg 7 wrap 3.5mm spaced coil Ti of course on it. Oh and the resistance is right on what SE says it should be. The best I have used so far. Don't know how they are making it but it is a new Ti. Don't know how it will clean up using the method I use which is hot tap water and a brush but it is very smooth just dull in color.

I am waiting for my Bachelor to arrive from China so I haven't used it yet, but knowing your vaping style the Bachelor should work out well for you being an regular STM user. We will have to see once we get them in our hands.

 

[Vlad1]

I am waiting for my Bachelor to arrive from China so I haven't used it yet, but knowing your vaping style the Bachelor should work out well for you being an regular STM user. We will have to see once we get them in our hands.

I ordered some goodies from FT over their holiday, received notification on the 15th everything packed and shipped but still showing up as "Item not found" when I try to track it. I should know better to order something I really want from them as I know it's going to take a while to receive, but I just cant help myself sometimes.

 

[Quantum Mech]

Hey Mech if you are lurking I see that efun has those for 20 bucks but they are out. Fastech is 23 and eciggity is 24.99. For $1 I could get it in 3 days instead of 3 weeks but if efun had them I might go for that.

my only real option here is fasttech or I pay through the nose in the UK

 

[2legsshrt]

my only real option here is fasttech or I pay through the nose in the UK

Yeah not sure what I'll spend my 2 cents on. I see why you guys like the 24 It seems to be smoother and warmer. A little tough to get in between the screw and the post on the STM but worth it.

 

[Quantum Mech]

Yeah not sure what I'll spend my 2 cents on. I see why you guys like the 24 It seems to be smoother and warmer. A little tough to get in between the screw and the post on the STM but worth it.

Wick, can never have enough wick

 

[2legsshrt]

Hey is there a thread on the IPV 5 or is it not very popular. I did read that it has the same rings in the battery compartment that the R DNA200 has. Doesn't it have reverse battery protection either. Don't know just isn't alot out there like when the SX comes out with something new

 

[2legsshrt]

Wick, can never have enough wick

I can see where the Bachelor at least on the review I saw could take a 4mm coil. Surely you could get enough in there.