Oh boy! APV here I come.

[planes]

The Evod twist and MPV2 are very good but I need more. As I see it, those two are back-ups and travel devices. I need a bada$$ set-up that provides volumes of vaper so I need an apv. I'm happy with the MVP2 especially with the ohm reader but not sure if it can take me where I want to go.

I've already built several coils with success and see that I can only get so much out of the MVP even with 1.5 and 1.8 coils, unless I'm missing something of course. Maybe 3 coils is not enough and I need 28 instead of 32 gauge to wrap 12 loops on the coil as I've seen on Youtube. If that's case, I'll buy some 28 and I'll go back to the laboratory. But it still seems like trying to squeeze blood from a rock. Please chime in.

If that's correct and I need to look to an apv, then this is the route I want to take.

1. A mod
2. A drip atomizer.(Is that the right wording?) I really like to sample multiple juices at one sitting. 5-7
3. tanks, I'm fine with and happy with the 2 mini pt2's and the one pt3 I have.

I'm looking at a VV VW device with wattage up around 15 to 18 and volts at 10?

This eliminates the Provari which is fine because I don't need to spend that much.

Any suggestions would be helpful.

 

[crxess]

Slow down and look around.

Oh, and MVP2.......it is an APV

Now, if you are looking for 15w and over, you will likely end up with a Vamo or similar or Spend quite a bit more for a High end APV like something with a DNA 20 controller.

Personally I think what you are wanting to do would work better with a Good Mechanical Mod and decent Batteries.

 

[JmanEspresso]

yeah from what im getting the feeling your wanting, a mech and high amp/high drain batteries would do nicely. And an RDA of your choice, of course.

 

[WarHawk-AVG]

If you want over 15watts..the only rigs that go up that high are the DNA20 devices (soon to come the DNA30 which can throw up to 30 watts)...they are nice..but VERY pricy
The Duke 1.4 can throw up to 50 watts The Duke v1.4

MVP2 is a APV, it does well if you are a normal vaper and not one that wants mega power and lots of clouds

NexGen Vapor | The Utimate DNA 20 Ecig
http://jcmsvapes.com/APV-Mods/DNA20-Mods

Good luck

 

[Sickkboy]

If 15-18 watts is what you need then you have to look into DNA20 mod, and they kinda pricey, most of them are expensive than provari though.

Rebuildable dripping atomizer (RDA) that I see most of this forum suggest and I agree with are Igo-l for a single coils and Igo-w for a dual coils, both have large platform so you can build coils easily. And both are really cheap around 15 bucks I believe

Tanks, I don't know if you mean rebuildable too? but if it is then RSST is kinda be the most easiest rebuildable tank atomizer (RTA) to start with. This RSST is around 20 bucks.

 

[planes]

The DUke isn't really out of my price range but I'm trying to steer away from the box mods. Not sure I want to go the mechanical mod route as I want some protections. I've been looking at the Vamo 5. Can I get most of what I want from this mod?

 

[crxess]

Vamo 5 I don't know the build or functionality - to many cloned versions.
I have an original First run Vamo from Rainbow Heaven. Running dual 18350's it will punch anything I own to 15w without breaking a sweat. That said, I rarely do it. Don't like stacking batteries.

All my Mechanicals can do the same thing and more with 1 18650 MNKE battery and the right ohm coil setup.

Built in protection? VapeSafe fuse

All the other protection built into a mod is to protect the circuit board from damage. No board in a Mech to damage.

 

[UncleChuck]

If you want high-power, with regulation, at a low price point, your best bet is either a Zmax or a Vamo in stacked 18350-mode only. With a single battery, they aren't going to put out any more power than your MVP already does. But with stacked batteries, and the device set to voltage mode, you can get into the 20+ watt range. You must be in voltage mode, and run stacked batts though.

I'm currently running a 1.5ohm 28g build at 6v on my Zmax. The maths say that's around 25 watts, it may be a bit lower due to efficiency and all that, but it definitely runs on par with my subohm setups.

 

[planes]

If you want high-power, with regulation, at a low price point, your best bet is either a Zmax or a Vamo in stacked 18350-mode only. With a single battery, they aren't going to put out any more power than your MVP already does. But with stacked batteries, and the device set to voltage mode, you can get into the 20+ watt range. You must be in voltage mode, and run stacked batts though.

I'm currently running a 1.5ohm 28g build at 6v on my Zmax. The maths say that's around 25 watts, it may be a bit lower due to efficiency and all that, but it definitely runs on par with my subohm setups.

I'm coming to that realization and was seriously looking at the Vamo. Haven't read much about the Zmax but I'll look into them. I'm not real keen on doubling up on batteries. What really caught my eye was the hybrid, Valkyrie but it's out of stock, expensive and with issues.

I ordered two drip atomizers last night from myvaporstore to up the vape ante. I'll throw together some 1 ohm coils and drip which might be what I'm really after, just want real good flavor and throat hit. Should have them by the end of the week.