Does one just use a drop of glue or what? I have it and I think it will be much more user friendly if I can figure out how to affix.
On/Off cap cover, How do you install?
- Thread starter Steelgirl
- Start date
- th_trl_thread_readers 0
- Status
Is it brass or aluminum?
If it is aluminum it should just press on. The brass covers come with a string. Lay the string over the button and press the cover on over the string. Trim off the extra string. Make sure in either case that the button is turned to the locked position before you press on the cover.
If it is aluminum it should just press on. The brass covers come with a string. Lay the string over the button and press the cover on over the string. Trim off the extra string. Make sure in either case that the button is turned to the locked position before you press on the cover.
Last edited:
It looks like hard plastic to me. It's black, no strings. I did have at the OFF position. The cap cover swallowed the switch and if I try to turn it, the new top cap just spins, but does not turn anything.
That's the delrin cover. Sorry, I have no experience with that one. I'm sure help will be along shortly.
Try a piece of dental floss in lieu of the string, I re-installed my brass cover and that is what I used.
Lock the firing pin first. Get some dental floss aka "string" - and lay that over the top of the button as you push the delrin button cover on. Trim off the ends. Unlock the firing pin.
T
T
BTW - you don't want to use glue, because you may want to get the cover off to reset it at some future time. An example is lazy Trunker that never cleans his mod and just presses harder and harder on the button cover, until eventually the firing pin does not touch the battery!! mod needs a good clean and file of the firing pin.
http://www.reosmods.com/index.php?option=com_virtuemart&page=shop.browse&category_id=34&Itemid=3
Clean the damn mod Trunker! Like that ^
Replace button cover so the newly clean mod fires just right again...Lock it - prise the cover off and get a bit of string....
T
http://www.reosmods.com/index.php?option=com_virtuemart&page=shop.browse&category_id=34&Itemid=3
Clean the damn mod Trunker! Like that ^
Replace button cover so the newly clean mod fires just right again...Lock it - prise the cover off and get a bit of string....
T
I had a piece of thick bounty paper towel in my hand and a light bulb went off. Cut a tiny strip and did just as instructed. One tiny sliver still visible, but it good cuz I can see if the cap has accidentally gotten turn to off position. Thanks all, for the clarification.
I use the tails trimmed from cotton wicks, it holds tight and I am always finding them stuck to everything or laying around so the supply is nearly unlimited.
I just went through this yesterday.
I received my new neon yellow from Rob along with a black delrin button. I locked the switch and pressed on the button and unlike my aluminum buttons before it the delrin just bottomed out. I thought I broke the lock, but not the case. I got on the horn with Rob to begin a chewing sesh and he explained to me that I must have gotten an old version button in that it was drilled much deeper than the current generation. He also explained to me that the problem can be rectified with a small (1/8th-3/16th inch) length of tygon (squonk tube) that acts as a spacer. It took me two tries (1st one too short) and I was up and vaping.
good luck.
I received my new neon yellow from Rob along with a black delrin button. I locked the switch and pressed on the button and unlike my aluminum buttons before it the delrin just bottomed out. I thought I broke the lock, but not the case. I got on the horn with Rob to begin a chewing sesh and he explained to me that I must have gotten an old version button in that it was drilled much deeper than the current generation. He also explained to me that the problem can be rectified with a small (1/8th-3/16th inch) length of tygon (squonk tube) that acts as a spacer. It took me two tries (1st one too short) and I was up and vaping.
good luck.
LOL. We all use something different to hold that bugger on. I didn't have any dental floss at the office when I got mine so took some plastic bag from some parts and cut a chunk and placed it between the button and the cap. Pushed down and the excess plastic cut right off. Holding like a champ.
Hey, I saw a yellow Grand for sale yesterday on the site,. Does that look like your color? You'll have to post a picture of that beauty. Looks like a nice safety yellow. You shouldn't have any issues crossing the street holding it out front! Looks nice!
this isn't mustard yellow..This pic doesn't capture the sheer brightness of the yellow, look how dull the Kawasaki green looks next to it. The KG is very bright, this one is off the charts.
Last edited:
Like!! You must have just gotten that because you didn't bring it with you when we met up.
- Status
