Hi,I have a big problem with my Taifun GT, and i would like some answers because i'm going crazy.
I created a mesh of 3,7cm and put into the taifun GT with, on top, 2 x 2mm wick , like a vagina
so as this : ( I ) , where ( is wick and I is mesh.
My friend knows well this atomizer, and he helped me with this config because for him 2 meshes on top can better irrorate the mesh giving better taste.
In fact vaping is very good, but every day I have a big problem that I can't fix. I'm using kanthal 0,3 ribbon, but i had problems also with 0,2 and 0,4 wire .
The problem is this: the coil never remains the same, also if properly builded. I can vape for one day (normally less), and when i close the top of the smokestack (I doesn' t close it tight) , the coil is perfect, all the spirals turns orange together or in few moment later. In fact i svape well ,very well, but after some hours, when I feel a strong drag ( i'm a little asmatic so my breathe becomes hard and short) with few fog, I understand that singles spirals on coils mooves inside atomizer.
In fact I open the tank, I do a dry burn (not washing with water but directly with liquid on mesh) and when all the liquid evaporate, only the first spiral or the first and the last becomes very white, near to brake(hot spot). I can' t understand why. Mesh is good and well oxided, because mooving spirals again, those works well.
I also tried with another mesh, and different coils (tight or wide around mesh), of different types , as written first, but the result is always the same.
I see that the problem isn' t that base turns or mooves when i close the smokestack or i put the tank. "taifun gt" logo still remain on that point, so base doesn't moove.
Wicks and mesh are correctly cut, so doesn' t comes out too much from the smokestack, so they doesn't push on tank when i close it.
So how the coil mooves?? Now every single spiral is tight to mesh and hard to moove, so why in 48 hours i already mooved them 3 times for this problem??
Help me, this atomizer is a bomb of flavour, but becomes a nightmare for this issue.
Another secondary issue. Sometimes a drop comes out from the air entrance: that is caused because the liquid inside smokestack fill inside the little hole under the mesh? If yes, how to avoid this?
UPDATE: Opening the smokestack, I saw that one turret do little movements..maybe is this that mooves single spirals?!
I fixed it with a little piece of wood at the base, now it doesnt' moove, but the problem still happens!! why?! also second one makes very little movements. I cut mesh shorter, now it's longer as the smokestack, so the tank mustn' t moove the coil, closing it.
I created a mesh of 3,7cm and put into the taifun GT with, on top, 2 x 2mm wick , like a vagina
so as this : ( I ) , where ( is wick and I is mesh.My friend knows well this atomizer, and he helped me with this config because for him 2 meshes on top can better irrorate the mesh giving better taste.
In fact vaping is very good, but every day I have a big problem that I can't fix. I'm using kanthal 0,3 ribbon, but i had problems also with 0,2 and 0,4 wire .
The problem is this: the coil never remains the same, also if properly builded. I can vape for one day (normally less), and when i close the top of the smokestack (I doesn' t close it tight) , the coil is perfect, all the spirals turns orange together or in few moment later. In fact i svape well ,very well, but after some hours, when I feel a strong drag ( i'm a little asmatic so my breathe becomes hard and short) with few fog, I understand that singles spirals on coils mooves inside atomizer.
In fact I open the tank, I do a dry burn (not washing with water but directly with liquid on mesh) and when all the liquid evaporate, only the first spiral or the first and the last becomes very white, near to brake(hot spot). I can' t understand why. Mesh is good and well oxided, because mooving spirals again, those works well.
I also tried with another mesh, and different coils (tight or wide around mesh), of different types , as written first, but the result is always the same.
I see that the problem isn' t that base turns or mooves when i close the smokestack or i put the tank. "taifun gt" logo still remain on that point, so base doesn't moove.
Wicks and mesh are correctly cut, so doesn' t comes out too much from the smokestack, so they doesn't push on tank when i close it.
So how the coil mooves?? Now every single spiral is tight to mesh and hard to moove, so why in 48 hours i already mooved them 3 times for this problem??
Help me, this atomizer is a bomb of flavour, but becomes a nightmare for this issue.
Another secondary issue. Sometimes a drop comes out from the air entrance: that is caused because the liquid inside smokestack fill inside the little hole under the mesh? If yes, how to avoid this?
UPDATE: Opening the smokestack, I saw that one turret do little movements..maybe is this that mooves single spirals?!
I fixed it with a little piece of wood at the base, now it doesnt' moove, but the problem still happens!! why?! also second one makes very little movements. I cut mesh shorter, now it's longer as the smokestack, so the tank mustn' t moove the coil, closing it.
