protank3
- Thread starter hachoo
- Start date
- th_trl_thread_readers 0
- Status
Hi hachoo, have you tried google and youtube before? Let me know if it's helpful?
I think we should all start using this really cool tool haha since a lot of questions are repeated. They have animations and all. Very interactive site overall 
http://lmgtfy.com
Sent from my SM-N9005 using Tapatalk
http://lmgtfy.com
Sent from my SM-N9005 using Tapatalk
Yeppy...am using Protank 3 mini. Its gives excellent flavour and 10-20% more vapour than my other PT2/Evod, provided you built your own coil.
Best to use NR-R-NR wire : http://www.e-cigarette-forum.com/forum/sg-vapers/536846-nr-r-nr-wire-new-sensation.html
Main Advantages over PT2 :
1) The slot hole is double that of PT2, hence able to suck in massive juices
2) Pin slides much more easily into the silicone rubber, unlike rubber on PT2, making your rebuild much easier.
3) Less tendency to have burnt taste due to double slot area to allow in more juice which is aligns with the larger air flow than PT2.
Tricks I use to get massive flavour and vapour:
1) Dump the stock dual coil. Use a single 2mm coil. Theres too much misconception about need to use dual coil.
single coil is easy to built and no need to fuss over dual coils, as it is known to create so much frustration that users reportedly throw the whole PT3 away, what a pity. Performance has no difference with duals provided you know the trick. In fact building dual coils is very tough, if not done properly, can easily result in almost no vapour, so I gave up.
2) Use cotton of course. I use NR-R-NR 1.5ohm, 1.8 or 2.2ohms.
3) Roll a 1.5 times thicker cotton than you use for PT2 on a 2mm screw driver, you need at least 2mm to have enough wicking to prevent leakage
4) As the rubber silicone top cap is long it pushes lower than PT2 but still the slot is double in area than PT2. Hence you need to position your coil at the centre.
5) Flatten both sides of cotton to fill the gaps.
6) It will not gurgle. There will be some leakage down to the positive post as usual for all clearomizers after 20-30 vapes. One way to stop the leakage is to add bottom flavour wick, but it will reduce vapour by a lot, so no point. coils will need minmal obstruction and adequate space for max oxygen.
7) the larger slot will suck in enough juice like no tomorrow, allowing massive vapour/flavour hence there's no burnt taste.
8) Some people complaint about the larger air hole. But its design this way to cope with the large slot to let in more air, a god send. Its actually not too airy but airy enough to allow lung-lung inhale or mouth-tolung, rather versatile.
Its a real chilli padi. Can only comment about the mini version, but most reviewers say the mini performance better than the larger tank PT3.
Enjoy the awesome vape!
Best to use NR-R-NR wire : http://www.e-cigarette-forum.com/forum/sg-vapers/536846-nr-r-nr-wire-new-sensation.html
Main Advantages over PT2 :
1) The slot hole is double that of PT2, hence able to suck in massive juices
2) Pin slides much more easily into the silicone rubber, unlike rubber on PT2, making your rebuild much easier.
3) Less tendency to have burnt taste due to double slot area to allow in more juice which is aligns with the larger air flow than PT2.
Tricks I use to get massive flavour and vapour:
1) Dump the stock dual coil. Use a single 2mm coil. Theres too much misconception about need to use dual coil.
single coil is easy to built and no need to fuss over dual coils, as it is known to create so much frustration that users reportedly throw the whole PT3 away, what a pity. Performance has no difference with duals provided you know the trick. In fact building dual coils is very tough, if not done properly, can easily result in almost no vapour, so I gave up.
2) Use cotton of course. I use NR-R-NR 1.5ohm, 1.8 or 2.2ohms.
3) Roll a 1.5 times thicker cotton than you use for PT2 on a 2mm screw driver, you need at least 2mm to have enough wicking to prevent leakage
4) As the rubber silicone top cap is long it pushes lower than PT2 but still the slot is double in area than PT2. Hence you need to position your coil at the centre.
5) Flatten both sides of cotton to fill the gaps.
6) It will not gurgle. There will be some leakage down to the positive post as usual for all clearomizers after 20-30 vapes. One way to stop the leakage is to add bottom flavour wick, but it will reduce vapour by a lot, so no point. coils will need minmal obstruction and adequate space for max oxygen.
7) the larger slot will suck in enough juice like no tomorrow, allowing massive vapour/flavour hence there's no burnt taste.
8) Some people complaint about the larger air hole. But its design this way to cope with the large slot to let in more air, a god send. Its actually not too airy but airy enough to allow lung-lung inhale or mouth-tolung, rather versatile.
Its a real chilli padi. Can only comment about the mini version, but most reviewers say the mini performance better than the larger tank PT3.
Enjoy the awesome vape!
Last edited:
Nice write up about mini PT, use with evod is best
You might want to enlarge the air hole slightly bigger and the quality outshine other tanks
Setbacks are requiring to refill tank and also has some leaking if you don't wick it properly, other than that mini PT is a good small tank for outdoor
Enlarge air hole using with evod
Using NR-R-NR 1.5ohm produces huge cloud close to KFL
Sent from Gotham City using Tapatalk
You might want to enlarge the air hole slightly bigger and the quality outshine other tanks
Setbacks are requiring to refill tank and also has some leaking if you don't wick it properly, other than that mini PT is a good small tank for outdoor
Enlarge air hole using with evod
Using NR-R-NR 1.5ohm produces huge cloud close to KFL
Sent from Gotham City using Tapatalk
Just go the the pharmacy and get the sterilized cotton ball. So far I never boil it or get the cotton wick
Sent from Gotham City using Tapatalk
I don't boil my sterilized cotton too. Just use straight from the bag. Best is transfer the cottons to a ziplock or seal the bag after opening to prevent funny smells from getting into your cotton.
I boiled my sterile cotton but I notice no extra particles in water.. no difference in taste..its just for piece of mind
... anyway, boiling cotton and drying is a very easy process..just boil a handful amount..dab it dryer and flatten it using paper towel to dry faster
...then place them on paper towel to allow the paper to help adsorb the water thru diffusion process.
.it'll dry up after only after two days..then can last for months of usage..
... anyway, boiling cotton and drying is a very easy process..just boil a handful amount..dab it dryer and flatten it using paper towel to dry faster
...then place them on paper towel to allow the paper to help adsorb the water thru diffusion process.
.it'll dry up after only after two days..then can last for months of usage..
How long you been vaping??? Fogger v 4 is a dual coil built and you sound like you just started...
Sent from my iPhone using Tapatalk
Fogger V4 looks easy but need some experience to perform an even coil on both sides and wicking it just nice near the juice drain
Sent from Gotham City using Tapatalk
Currently using pro tank 3 mini. own a protank 2 also. protank3 mini totally win over protank 2. vapour production and taste is so much more then protank 2. my friends using protank 2 also complain kinda leak. hope this info is useful to u. just my personal opinion only. u should try aerotank also, not bad for a tank that uses stock coil if you are the one who are laxy to coil ur own like Russian or kayfun.
- Status
Similar threads
