Provari with Kayfun Lite Plus

[mrdfield]

Hi all. Just wondering I am using a provari with a kayfun lite with a 1.8 ohm coil bulid
and i am just wondering what others are running there volts at with a similar setup
I am running at 4 volts and been playing around with the volts and need some guidance

 

[thmstwwng]

I have a kayfun lite plus v2 with 1.5 ohm 28 g using p3 running at 8 - 12 w. Loving every puff of it

 

[rollcoil]

I have a ProVair 2.5, kayfun Lite Plus v2 with 1.5ohm - (7 wraps, 5/64th drill, 30ga Kanthal ). Usually running around 4.0v to 4.2v.

 

[ENAUD]

I like my Kafun's at 1.4Ω-1.6Ω with 30 gauge Kanthal, 3/32" compressed coil. I run them at V= Ω+2. That being said, right now I am vaping one at 1.8Ω at 3.8V

 

[ProV P3T3]

I have a kayfun lite plus v2 with 1.5 ohm 28 g using p3 running at 8 - 12 w. Loving every puff of it

I'm sure that Kayfun Lite Plus works great with the P3. I have a silve P3 (Bet version) but was thinking of ordering a black P3 now that they have been released. I want to get an all black KL+ to make a Stealth version P3 setup.

 

[WillyZee]

I usually vape mine at 1.8ohms and use 3.6- 3.8V

 

[MonsterKenny]

Same here 1.5-1.8ohms, i use a russian 91% but its the same atomizer I tend to vape at 4.2v

Ken

 

[AstroTurf]

..........

 

[Train2]

You are right around where I would be...

I do tend to shoot for more like 1.4 ohms, but wherever I land, I usually START about ohms+2 for my voltage, as Enaud said, but then, as long as they're wicking good, bump it up .1 or .2 more.

Hi all. Just wondering I am using a provari with a kayfun lite with a 1.8 ohm coil bulid
and i am just wondering what others are running there volts at with a similar setup
I am running at 4 volts and been playing around with the volts and need some guidance

 

[Zombo]

I'm using a Lemo ( Kayfun-inspired) at 1.25ohms and 12w. I was shooting for 1.8, but, as a first-timer, I considered myself lucky and kept it. I have it on 2-3 boost (depending on mood).

 

[Baditude]

Using an authentic KFL+ with 28 gauge Kanthal, anywhere between 1.3 - 1.6 ohm single microcoil, usually between 3.5 - 4.0 volts depending upon the flavor/e-liquid being used. I've been using the cotton nest technique with either rayon (synthetic cotton) or organic cotton as the wick material. Version 2.5 Provari standard or mini.

 

[kas122461]

It is nice to see a post from you again Mr. Baditude, I have been missing your posts, I hope you are doing alright.

KAS

Using an authentic KFL+ with 28 gauge Kanthal, anywhere between 1.3 - 1.6 ohm single microcoil, usually between 3.5 - 4.0 volts depending upon the flavor/e-liquid being used. I've been using the cotton nest technique with either rayon (synthetic cotton) or organic cotton as the wick material. Version 2.5 Provari standard or mini.

 

[Kasanova]

i also have a lite+ v2 at 1.5, but i run it at 4.2-4.5 volts. i like a warm vape.

 

[1/2 fast]

Just built a Lite+ to 0.9 ohms this afternoon. Running it at 11 watts/3.6 volts on a P3. But I like a cooler vape when I'm doing fruity flavors.

 

[Kloudz]

I'm running a Ehpro kayfun 3.1 28g 9 wrap at 1.8ohm on 4.0v on my Provari. The taste and clouds are incredible. I just hate how I have the center pin on the kayfun screwed all the way in and I'm left with a gap.

 

[xstitch]

I'm running a Ehpro kayfun 3.1 28g 9 wrap at 1.8ohm on 4.0v on my Provari. The taste and clouds are incredible. I just hate how I have the center pin on the kayfun screwed all the way in and I'm left with a gap.
View attachment 392134

A beauty ring will hid the gap for you!!

 

[Kloudz]

I got a beauty ring for it, it's just silly loose.

 

[AstroTurf]

Sand down the center pin on the Kayfun.

 

[xstitch]

I got a beauty ring for it, it's just silly loose.View attachment 392190

You can try putting a spare o-ring under the beauty ring, I've done that before!


Sent from my iPhone using Tapatalk

 

[PapawBrett]

Sooo.... what would be a better fit atop a P2 - an HCigar or an Ehpro ?