Ok i ordered a v2 from madvaps and bought a 1835 and 1634 battery and charger, now what do i need to get it working when i get it. any and all info i can get is welcome. as this is all new territory for me
thanks
thanks
roughstak mod
- Thread starter past master
- Start date
- th_trl_thread_readers 0
-
- Tags
- madvapes
- Status
Probably a several more atomizers, some more cartridges and some sample e-liquids. Check out some of the suppliers on the forum main page, do a little shopping around for sample packs and prices. You'll need stuff for a 510, that's the connection on a RoughStack.
I love my Roughstack and hope you'll love yours just as much. Just for clarification, you just bought the Roughstack or the Roughstack and an extension tube or the maxi Roughstack ? You will use one 18350 batt in the small tube that comes with the Roughstack for 3/7 VT vaping and you can use the 18650 batt in the long tube for 3.7 Vt vaping or 2 16340 batts in the long tube for 6VT vaping or 2 of the 18350batts in the long tube for 7.4 VT.
Depending upon what voltage vaping you intend to do you will need different ohm attys or cartomizers depending on what you prefer to use or want to try.
I prefer LR 510 attys with Drip tip for doing 3.7 VT vaping on my roughstack or dual coil cartomizers. I don't choose to do 6 or 7.4 Vt vaping but if I did I would need some HV attys at 5 ohms.
Depending upon what voltage vaping you intend to do you will need different ohm attys or cartomizers depending on what you prefer to use or want to try.
I prefer LR 510 attys with Drip tip for doing 3.7 VT vaping on my roughstack or dual coil cartomizers. I don't choose to do 6 or 7.4 Vt vaping but if I did I would need some HV attys at 5 ohms.
was going for the maxi but wasn't in stock and didn't know what i needed that on for anyhow
Roughstack w/ 4.8 volt batt is on my wish list.
I think 4.8 volts will be nice w/ dual coil.
I think 4.8 volts will be nice w/ dual coil.
Ok, so you're got the shorter version that will take the one 18350 battery and do 3.7 VT vaping. In that case get yourself some 510 LR attys and drip tip and dual coil cartomizers (1.5-1.6 ohms). Enjoy !
Yes, the longer tube is the maxi. The longer tube is the one that takes either one 18650 battery, two 16340's or two 18350's. You can pick that longer tube up by it self sometime in the future when its in stock if you decide you want to do that later on. The 18650 battery last a really long time between charges and the other batteries that you can use in the longer tube allow you to do either 6 or 7.4 Vt vaping if you wish.
The maxi rocks because you can hit it at 3,7, 5(well 4.8 volts). 6 or 7.4 volts(if you do this...and like it...your my(sick)hero).
Screw the atties...get some dual coil cartos (they will work at any voltage on the maxi) and vape your head off.
the RS is a true workhorse....reliable..dependable...and at the price they sell for you can have 2 or 3 for backups.
Screw the atties...get some dual coil cartos (they will work at any voltage on the maxi) and vape your head off.
the RS is a true workhorse....reliable..dependable...and at the price they sell for you can have 2 or 3 for backups.
Depends on the 18350s. The protected li-on 18350s madvapes sells will not stack in the maxi rough stack V2. It won't close all the way. A couple of IMR 18350s will stack in the maxi RS v2.
Also mentionable is that the ni-mh 4.8v 17650 fits the maxi for ~5.0v vaping.
They usually have a lower mah rating than a li-on. They feed amps better than li-on as they drain. And, they produce more amps at the same voltage.
==
- Status
Similar threads
