Safely Vaping.

Status
Not open for further replies.

Matty316

Super Member
ECF Veteran
Mar 29, 2014
370
443
Hull, England
On a single battery mech mod it's not safe. With a dual parallel mech mod theoretically it's possible as the amp draw is devided between each battery so 14 amps will be drawn from each battery. But at this low resistance you would have very little wiggle room with 20a batteries. any sort of short or loose leg in a post could easy put you down as low as .1 ohm at which point you would be drawing 42 amps which is passed the safe limit for 2 20a CDR batterys run in parallel.

I wouldn't recommend anyone build that low on a mech even a dual parallel one myself. But if you're going to then you would be much safer running 2 30a CDR batteries like sony vtc4's in parallel which would give you a much better safety cushion.

1.0 ohm = 4.2 amp draw
0.9 ohm = 4.6 amp draw
0.8 ohm = 5.2 amp draw
0.7 ohms = 6 amp draw
0.6 ohms = 7 amp draw
0.5 ohms = 8.4 amp draw
0.4 ohms = 10.5 amp draw
0.3 ohms = 14.0 amp draw
0.2 ohms = 21.0 amp draw
0.15 ohms = 28 amp draw <---------------
0.1 ohms = 42.0 amp draw
0.0 ohms = dead short = battery goes into thermal runaway
 
Last edited:

edyle

ECF Guru
ECF Veteran
Verified Member
Oct 23, 2013
14,199
7,195
Port-of-Spain, Trinidad & Tobago
Hi again guys. I just need to know: can I vape safely at 0.15 ohms with a parallel mod with two 20 amp batteries? I need to know, as I normally vape at this level, and will affect whether I get another regulated mod or whether I get a Tuglyfe mod. Thanks!

No.

Your safety depends on your knowledge and attention to your hardware.
"parallel mod" ? That tells me you're not safe; you could have said a lot more about the mod.
"two 20 amp batteries"? That tells me you're not safe: you could have said exactly what batteries, and where you got them from, plus for vaping that low I'd expect to see vtc4.

"another regulated mod"?
could it be that you are using a regulated tc mod? dunno, again you didn't say; but if it's a tc mod that changes everything.
 

Boden

Vaping Master
ECF Veteran
Sep 7, 2012
5,516
28,164
Lexington KY
On a single battery mech mod it's not safe. With a dual parallel mech mod theoretically it's possible as the amp draw is devided between each battery so 14 amps will be drawn from each battery. But at this low resistance you would have very little wiggle room with 20a batteries. any sort of short or loose leg in a post could easy put you down as low as .1 ohm at which point you would be drawing 42 amps which is passed the safe limit for 2 20a CDR batterys run in parallel.

I wouldn't recommend anyone build that low on a mech even a dual parallel one myself. But if you're going to then you would be much safer running 2 30a CDR batteries like sony vtc4's in parallel which would give you a much better safety cushion.

1.0 ohm = 4.2 amp draw
0.9 ohm = 4.6 amp draw
0.8 ohm = 5.2 amp draw
0.7 ohms = 6 amp draw
0.6 ohms = 7 amp draw
0.5 ohms = 8.4 amp draw
0.4 ohms = 10.5 amp draw
0.3 ohms = 14.0 amp draw
0.2 ohms = 21.0 amp draw
0.15 ohms = 28 amp draw <---------------
0.1 ohms = 42.0 amp draw
0.0 ohms = dead short = battery goes into thermal runaway
It isn't truly a 50/50 split between the batteries, differences in internal resistance of the batteries will set the draw from each. Also because you have two batteries next to each other mutual heating will de-rate them a bit further.
 
  • Like
Reactions: Mooch

Scotticus93

Super Member
ECF Veteran
Verified Member
Nov 18, 2013
934
415
Yorktown, Virginia, United States
On a single battery mech mod it's not safe. With a dual parallel mech mod theoretically it's possible as the amp draw is devided between each battery so 14 amps will be drawn from each battery. But at this low resistance you would have very little wiggle room with 20a batteries. any sort of short or loose leg in a post could easy put you down as low as .1 ohm at which point you would be drawing 42 amps which is passed the safe limit for 2 20a CDR batterys run in parallel.

I wouldn't recommend anyone build that low on a mech even a dual parallel one myself. But if you're going to then you would be much safer running 2 30a CDR batteries like sony vtc4's in parallel which would give you a much better safety cushion.

1.0 ohm = 4.2 amp draw
0.9 ohm = 4.6 amp draw
0.8 ohm = 5.2 amp draw
0.7 ohms = 6 amp draw
0.6 ohms = 7 amp draw
0.5 ohms = 8.4 amp draw
0.4 ohms = 10.5 amp draw
0.3 ohms = 14.0 amp draw
0.2 ohms = 21.0 amp draw
0.15 ohms = 28 amp draw <---------------
0.1 ohms = 42.0 amp draw
0.0 ohms = dead short = battery goes into thermal runaway
I agree with him. Run two vtc4 batts. I would personally run it in a regulated mod but that's up to you.
 

Revelene

Super Member
ECF Veteran
Sep 29, 2013
576
474
Kentucky, USA
The OP states in the first line of his post that he is using two 20A batteries. o_O

I see that. He must have edited it soon after posting or my lack of sleep has caused me to misread it... Though, I swear it didn't say two 20a batteries before...

That said... I think the OP needs to read up on electricity before proceeding any further.... and I have no clue what a "Tuglyfe mod" is.
 

yuseffuhler

Ultra Member
Mar 28, 2015
1,341
1,348
Houghton, MI
I see that. He must have edited it soon after posting or my lack of sleep has caused me to misread it... Though, I swear it didn't say two 20a batteries before...

That said... I think the OP needs to read up on electricity before proceeding any further.... and I have no clue what a "Tuglyfe mod" is.
An unregulated dual battery mod. Wired in parallel if I remember right.
 
  • Like
Reactions: opticruby

tj99959

ECF Guru
ECF Veteran
  • Aug 13, 2011
    15,118
    39,615
    utah
    The only time there is any value to building below .5 is when there is money on the line at a cloud competition.

    And, even then, the cloud is mostly related to the capacity of an individuals lungs. Coil resistance is a distant 2nd.
    So if you want to blow huge clouds, you will be better served by learning how to develop stronger lungs.

     
    Last edited:
    Status
    Not open for further replies.

    Users who are viewing this thread