Showing Off those MODS

[MASTER0FDAMPF]

I just thought that since so many MV users are happily builing mods from MV kits that it was time for a thread to show off. I will kick it off with my newest creation. Feel free to post you newest builds!

The WiiGo
Wii candy dispenser! I used a top cap from a fried ST eGo, all other parts are from a MV box kit. Still trying to figure out how to make the button better.

I have a few more of these so I will likely build a couple more.

 

[MASTER0FDAMPF]

Although Not a mod I thought some people would get a kick out of this one:

I blend my Juices (ordered from MV, of course). You are looking at 1000 ml of pure golden goodness known as Dampf #6 Blend!
How Ironic is it that 1000ml of liquid fits so snugly in one of my old cig cartons?

 

[wolfstone5]

I love the Wii controller!!! I was thinking about doing the same thing in white.

 

[chillinwatook]

a wii-cigarette..... awesome.....

 

[intriqken]

Keep pics and ideas coming,
I'm itching to make a new mod or two and just want ideas

 

[MASTER0FDAMPF]

I found a minature atari joystick and the stem is about the size of a 510 connector. I think that will be my next one...Gotta put an order in for more supplies though...and probably a blue lightning (I have been saving up reward points for one)

 

[Rainz]

My 3.7 MV box - Put it together about a week ago... love it! Hits like a beast with High drain 14500/1.5 ohm LR 510 atty. I used the .5a switch, 3mm blue LED, and a piece of a 16g needle for feeding. Drilled a hole in 3ml bottle cap and used JB weld to secure a small piece of flexible tubing there... haven't had one drop of juice leak into the box. Over squonked a few times to get some overflow on top though. It's definitely something you have to get a feel for. So my volt is mostly parked for now, on standby for specific outings

 

[MASTER0FDAMPF]

That is pure awesomeness!!! What did you use to make the injector tube going to the atty?

 

[Rainz]

Thanks MoD(no pun intended) Not sure if this is what you were looking for; I popped out the center of the 510 connector, and soldered the piece of needle along with the pos. wire in there... was tight fit, and took some fiddling to get the wire along side the needle, but worked well as just a little solder sealed the hole nicely. Then reinserted the center pole into 510 connector.

If your question is about the silicone tubing... I just drilled a small hole(go smaller if you try this... I buggered the first cap) in the 3ml bottle cap, smaller than needed to fit tubing in, then widdled it to size with a nail. Cut a piece of tubing longer than I needed(about .5"), inserted into cap hole, and secured it with JB weld. That also took some fiddling to get the tube just barely into the cap hole. No way I could have done this without JD Weld, what great stuff! ...then just trimmed to fit needle. I also cut silicone tubing to go inside a few 3ml bottles... no fiddlin there, dripper tip has prong inside, it slides on nice and tight... so i just have to use this cap, but can have several filled bottles standing by. Hope this helped.

edit; (16g lure lock from madvapes, snipped w/ wire cutters. Had to open the crimped/cut end with pliers... that's why it looks square on the inside end in the previous post pic)

 

[Rainz]

... also wanted to add... couldn't have assembled this without Mr. Helping Hands

 

[MASTER0FDAMPF]

Helping hands are a must...I have one on the soldering bench and one at assembly area. Just cheap ones from itt (Illinois tool). although it seems you took the magnifier off (or I just have a very cheap "deluxe" model )

The needle bit was the part I was wondering about. Thanks a ton, I will have to give that a shot with the next round. My next will mod will have the button as the d-pad and I think I will try to make the A button a squonk button...

... also wanted to add... couldn't have assembled this without Mr. Helping Hands

 

[Rainz]

The Wii-mod is pretty awesome! There's just no end to the creativity in these forums.

I ordered a couple of those duracell ipod powerpacks... gonna try these next.

http://www.e-cigarette-forum.com/forum/modding-forum/103067-duracell-mod.html

 

[MASTER0FDAMPF]

That is slick. I am now about to order more supplies...now I just need to find a few more hours in the day.

The Wii-mod is pretty awesome! There's just no end to the creativity in these forums.

I ordered a couple of those duracell ipod powerpacks... gonna try these next.

http://www.e-cigarette-forum.com/forum/modding-forum/103067-duracell-mod.html

 

[pwyll]

MadVapes' VV regulator board kit and 510 connector under all that silicone. Ratshack switch since I didn't have any MV horn buttons laying around (this was a kind of spur of the moment build).

. . .

 

[kcofohio]

Here are just a few of my "MV" component supplied mods.



3 5v and a 3.7v.

Now that I've read on the auto switch, that sounds interesting. Addictions, I tell you! lol

 

[Rainz]

very nice Pwyll ... I didn't think you could do VV in a 2 batt box. I may try one of these.

Is the box from madvapes?

 

[pwyll]

You can when the box is designed to be a usb charger running off two 18650's I actually had to order them directly from here as I have been unable to find them anywhere else, even on the Bay.

I think I might pop into the "What should MadVapes carry" thread...

 

[Jim211]

Not a kit but all parts came from madvapes. Coffin box,18650 battery,510 connector, horn switch and misc parts.

 

[dale1962]

Whats up Jim,long time no hear.....nice mod,see ya digging those tanks also

 

[Jim211]

Hey Dale,

Haven't had to build for a while but with christmas and being down to 3 mods its time to start building them again. The tanks are great but still use the dcc's when out running around.