SnowWolf 200w Box Mod with Temperature Control

Status
Not open for further replies.

Rixsta

The Millionaire Vapor' The Enabler
ECF Veteran
Verified Member
Apr 8, 2015
6,590
39,924
49
Somerset, UK
fa947k.jpg
ofomb.jpg


qzrmuo.jpg
10mlcat.jpg


2r79aiq.jpg
i2k860.jpg


30vzuq0.jpg
mkeyd0.jpg


8vn9xg.jpg
6ifimu.jpg


What a beast of a mod this is, now of course, 200 watts to me is a little daft but I didn't buy it for that, 100 watt and I would of still bought it, I mainly bought it for it's looks and temperature control feature.
It feels great in the hand and is the best looking mod I own by far, its like a fat iphone. It's simple to use, it automatically detect's if your using a kanthal type coil or a nickel coil, it wont work in temp mode if it's kanthal. Has a nice auto lock feature, hold the + and - together to change between watts and temperature, great easy to read bright display. It goes quickly through the wattage and after 150w goes into pulse mod when you vape, will I ever use it, probably not.
The build quality of this is superb, it feels and looks very expensive, the battery tray is held on by magnets and id say is 3 times, if not more stronger than the Segelei, it actually pulls it out of your hand they are that strong, it doesn't have any tray rattle if you push on it like my Segelei does either, no batteries move about, just a solid build. The spring 510 connection is very sturdy too, gives a good contact and reads my 0.25ohm coil at 0.26ohm, good enough for me.
It's just as easy to use as the Segelei, there are no menus or anything, it just works how it should. I'm waiting for my new tank to test the temp control so can't really comment on that yet.

Ok, cons, the first one isn't a con for me personally but others may find this device too heavy, it weighs a lot more than my Segelei but I like that..
It has glass panels either side, again, not really a con, they are very scratch resistant but I wouldn't like to drop it, it's going to smash unless your really lucky.
There is a very tiny button rattle from the power button but you have to put it close to your ear to hear it,
There is no battery percentage which I miss but really I'm just knit picking. Over the moon with it myself.
This isn't a review as such and Im not going into any great detail but any questions, drop a post below and I'll try and let you know..
So my fellow vapester's, what do you think ??
 
Last edited:

Rixsta

The Millionaire Vapor' The Enabler
ECF Veteran
Verified Member
Apr 8, 2015
6,590
39,924
49
Somerset, UK
I've seen these.
I wouldn't buy 1 as I like a smaller device and temp control doesn't interest me.
The main reason I wouldn't buy it is because of glass both sides!
I can guarantee I would drop this at some point and break it :( which would be quite annoying.

Ha yes but I've never dropped a mod like this, simply because I only vape it at home in the same spot, come to think of it, I've never dropped my phone either. The glass sides are finger print magnets and I've just ordered a carbon wrap for it..
 

paulparnham

Senior Member
May 25, 2015
183
81
55
Ha yes but I've never dropped a mod like this, simply because I only vape it at home in the same spot, come to think of it, I've never dropped my phone either. The glass sides are finger print magnets and I've just ordered a carbon wrap for it..
lol yes I'm baseing it on the fact i usually drop my phone at least once every 3 to 4 months. That's probably the reason why I use my mechs more than vw devices
 

Cullin Kin

Ultra Member
ECF Veteran
Verified Member
Jun 28, 2014
2,746
3,449
The 3Oh!3, Colorado
www.youtube.com
Mine comes tomorrow! I can't wait!!! It's such a gorgeous mod. I have my Ni200 wire, 4 batteries, and a Derringer all ready for it! I'm literally counting down the seconds.

I plan on doing a dry cotton burn test the second I get it! I never noticed that it doesn't have a battery percentage, but neither do my iSticks lol.

Edited the above because I misunderstood what you said lol.
 
  • Like
Reactions: triskelion

Rixsta

The Millionaire Vapor' The Enabler
ECF Veteran
Verified Member
Apr 8, 2015
6,590
39,924
49
Somerset, UK
lol yes I'm baseing it on the fact i usually drop my phone at least once every 3 to 4 months. That's probably the reason why I use my mechs more than vw devices
haha, sounds like my wife, she has smashed more screens than I care to mention. Good job she has insurance, hmmm, shame you can't insure mods .
 

Rixsta

The Millionaire Vapor' The Enabler
ECF Veteran
Verified Member
Apr 8, 2015
6,590
39,924
49
Somerset, UK
Mine comes tomorrow! I can't wait!!! It's such a gorgeous mod. I have my Ni200 wire, 4 batteries, and a Derringer all ready for it! I'm literally counting down the seconds.

I plan on doing a dry cotton burn test the second I get it! I never noticed that it doesn't have a battery percentage, but neither do my iSticks lol.

Edited the above because I misunderstood what you said lol.

Congrats, be prepared for the initial shock when you pick it up, then get prepared when the batteries go in, it's not the lightest of mods as I said before but I like it that way. I can't answer your Question about the battery telling you it's low because Im still above half charge on mine, battery life seems good, I'll have to get back to you on that one :thumb:
 

Rixsta

The Millionaire Vapor' The Enabler
ECF Veteran
Verified Member
Apr 8, 2015
6,590
39,924
49
Somerset, UK
how about you just mail me that snowwolf, i heard it is defective. id be glad to take it off your hands for free. just think of it as me saving you future headaches.
Well you have doomed me.....
I have only just noticed that the voltage doesn't display at all, it always reads 0.00v. The coil reads ok, the wattage is ok but no matter what tank you put on the mod, the voltage is always 0.00v, faulty !!!
Your cat has cursed me.
In the process of sending it back now and guess what, yes, they are out of stock now, brilliant :(

EDIT - I'll keep this here for others but its official, I'm an idiot, the voltage only shows in real time when you fire the device and it isn't faulty, so sorry to yourself and your cat :)
 
Last edited:

Smac61

Full Member
Mar 23, 2010
15
6
Detroit
3 days in now I'm loving mine. As far as impedance goes, I'm running a nickel temp build in it right now that reads .07 cold and its working flawlessly. Only issue so far is it doesn't always recognize an atty change. Sometimes I can just back it out and fire it "open" then screw the new atty back in for it to recognize the change, other times I have to slap a different atty on it, then switch back to the new one to get it to see it a new build. Hope that makes sense...
 
  • Like
Reactions: Cullin Kin
Status
Not open for further replies.

Users who are viewing this thread