Squonk Porn!

[Spydro]

I had one too and then it quit working like most of them did unfortunately. Never did have Rob redo it. I've got most of the different Reo models from the 14500 mini to a couple of Woodvils and a Grand. Haven't used them in years.

Sent from my SM-N960U using Tapatalk

When I first bought the OG VV Grand I sent it to Robert and asked him to go all through it, repair/replace anything it needed. I came back with an "as good a new" clean bill of health. IOW, it had been well taken care of by the person I bought it from. I only vaped it as a 'treat' now and then, so it saw limited use here. As pristine as it is the pevious owner might not of used it much either.
Altogether I acquired 37 Reos (but never scored a VV Woodvil) so do have examples of all of the rest of the models IIRC (and have multiples of many of them). The four 2015 Woodvil's pretty much retired all the other 7 Woodvil's, and the 5 P67's retired all the rest of the metal Reos until I stopped vaping last fall. All my vaping gear/spare parts/supplies/tools/etc are retired in storage.

 

[Highwayman1224]

When I first bought the OG VV Grand I sent it to Robert and asked him to go all through it, repair/replace anything it needed. I came back with an "as good a new" clean bill of health. IOW, it had been well taken care of by the person I bought it from. I only vaped it as a 'treat' now and then, so it saw limited use here. As pristine as it is the pevious owner might not of used it much either.
Altogether I acquired 37 Reos (but never scored a VV Woodvil) so do have examples of all of the rest of the models IIRC (and have multiples of many of them). The four 2015 Woodvil's pretty much retired all the other 7 Woodvil's, and the 5 P67's retired all the rest of the metal Reos until I stopped vaping last fall. All my vaping gear/spare parts/supplies/tools/etc are retired in storage.

I should have grabbed a P67 to add to my collection.

Sent from my SM-N960U using Tapatalk

 

[HigherStateD]

I should have grabbed a P67 to add to my collection.

Sent from my SM-N960U using Tapatalk

If I had a nickel for every mod I could say that about, I'd have a few more mods...

 

[Highwayman1224]

If I had a nickel for every mod I could say that about, I'd have a few more mods...

Yup... [emoji23] [emoji23] [emoji23]

Sent from my SM-N960U using Tapatalk

 

[Spydro]

I should have grabbed a P67 to add to my collection.

Sent from my SM-N960U using Tapatalk

FWIW, a bunch of Reos from Steamshack are up for sale in the classifieds that were bought during the close out sale for far less than retail. He had this: "Reo P67 "White with matching SL door" $117.50 plus shipping. Super light use. Few days. Still in like new condition. Will supply new tube and bottle along with the extras in a baggy the new mods come with."
So some P67's are still being sold.

I have 8 Grands (not counting the OG VV Grand), but for my uses the P67's were a huge improvement over the original Grands.

Pic of my five P67's all sporting Wotofo Profile Mesh RDA's (the one in front was custom made for me by Robert and is the only one ever made in this metallic copper color). Another custom one was slatted for right after this one, but he was in the process of shutting Reosmods down that I knew that was more important to him so I cancelled that one.

 

[Racehorse]

View attachment 901317 View attachment 901319 View attachment 901321

OMG you still have the Jaunty case too. Amazing. Yes, that was a pretty lil' piece and a very early one. I'm so glad you still have it, it really is one of the most gorgeous ones, before they stopped doing that finish. I'm glad it went to a good home to someone who would and still does, appreciate it!


THanks for this trip down memory lane!. So pretty!

https://www.e-cigarette-forum.com/attachments/reomini12-jpg.901319/

 

[Spydro]

While I have a lot of mech and regulated squonk mods, and endless bottom feed atty's for them, the Reo mods held the top shelf ever since the first one was acquired in August 2014. For a short time a favored atty on them was a Nuppin' (V1 & V2 versions, SS, Marine Brass, Anodized + accessory copper AFC's) with custom Syner and Loki Labs Router drip tips

So this picture of Reo 2015 Woodvil's and Grands was made more to show my V1 & V2 Nuppin's to Reonauts that were considered the cats meow by many of them during the short era that they were available (about 6-7 months, V1-late 2014 to V2-early 2015). Their unrestricted deck and MTL to restricted DL AFC's (3) made them versatile for either single or dual coils for many vapers. But as a unrestricted DL vaper I discovered that in a Nuppin' this high center coil style gave me truly stellar flavor from my DIY's in them.

 

[Doffy]

I should have grabbed a P67 to add to my collection.

Sent from my SM-N960U using Tapatalk

I think that there is one in the classifieds? Pretty good price. It is in the big reosmods collection thread if it is still available.

 

[Spydro]

Newer Reo mods with older atty's...

Reo P67's and bottom fed 2013 Vicious Ant Cyclones (with the desirable dished deck that their 2014 Cyclops didn't have). The dished deck was a reservoir of sorts to hold a little more juice to feed the wick between squonking. I bought both of these Cyclones used the summer of 2014, and both already had their AFC's drilled out perfectly for my favored DL vaping instead of the MTL size they had when new. They were definitely a noteworthy single coil flavor atty in their day and saw a lot of use on many of my metal Reo model's and 18650 Reo Woodvil's.

 

[ShowMeTwice]

KRMA RDA and an Armageddon. I grabbed four last year for $20 each and managed to get some cool side panels before they sold out.

I had to sand down ~2mm from the side panels to fit the v3 Armageddon's.

 

[Fstop]

Love it

Try it first with the recommended 6mm legs, as it may be different for you and how you vape. I got great flavour there - but when I dropped the coil down to 5mm legs, even better flavour and a lot smoother airflow. It's a bit harder to wick with the lower coil, just twist one end in, then pull it through. The well is a lot deeper than it looks too

Is this a AIO type unit? I've stayed away pods. & i want a cigarette with no mod in sight for a month

 

[Fstop]

Newer Reo mods with older atty's...

Reo P67's and bottom fed 2013 Vicious Ant Cyclones (with the desirable dished deck that their 2014 Cyclops didn't have). The dished deck was a reservoir of sorts to hold a little more juice to feed the wick between squonking. I bought both of these Cyclones used the summer of 2014, and both already had their AFC's drilled out perfectly for my favored DL vaping instead of the MTL size they had when new. They were definitely a noteworthy single coil flavor atty in their day and saw a lot of use on many of my metal Reo model's and 18650 Reo Woodvil's.

View attachment 902317
View attachment 902321

U a smoking vaping taste budman
engineer?
Here is my Woody

 

[HigherStateD]

My topside 90w, recurve OG, with my new frosted 22mm conversion cap.

 

[CMD-Ky]

My only spring drop came from one of those. I was new and, from that, I learned to use to ohm checker with the cap off and then again with it on. I had the luck of a fool, the spring worked as designed, it could have been a diaster.

Newer Reo mods with older atty's...

Reo P67's and bottom fed 2013 Vicious Ant Cyclones (with the desirable dished deck that their 2014 Cyclops didn't have). The dished deck was a reservoir of sorts to hold a little more juice to feed the wick between squonking. I bought both of these Cyclones used the summer of 2014, and both already had their AFC's drilled out perfectly for my favored DL vaping instead of the MTL size they had when new. They were definitely a noteworthy single coil flavor atty in their day and saw a lot of use on many of my metal Reo model's and 18650 Reo Woodvil's.

View attachment 902317
View attachment 902321

 

[Spydro]

My only spring drop came from one of those. I was new and, from that, I learned to use to ohm checker with the cap off and then again with it on. I had the luck of a fool, the spring worked as designed, it could have been a diaster.

A lot of vapers have had the same experience, both new vapers and old salts at vaping as well who forgot to do the final cap on check (a cardinal rule when using mechs, a DGI for any mod).

The high center build I pictured above on the Woodvil/Nuppin' was pushing the envelop because for the best results the coil had to be as close as possible to the top cap without touching it and creating a short. Why I mostly used this build in my black Nuppin's that had custom Delrin Syner drip tips that protruded a little down into the atty's chamber. It's Delrin served as a 'height stop gage' to get the coil as high as possible without touching the top cap.

Another build I did that 'flirted with danger' was a quad build in a very small space surrounded on all sides by a very close possible short. This one is on a Geekvape Avocado Genesis 22mm RDTA (pictured here on a TC mod) that I mostly ran on Noisy Cricket mech's, a well known dangerous mech mod. Both of mine had the Fat Daddy Kit in them that made them far safer.

 

[Spydro]

I have a lot of squonk porn pictures... might as well post another one.

Here's one I haven't used for years that dates back to 2015, The Black Widow. It's a black anodized Reo 2.1 w/LP door, and a black Nuppin' I ran a strong acerb DIY in that I called Poison.

 

[Skeebo]

A lot of vapers have had the same experience, both new vapers and old salts at vaping as well who forgot to do the final cap on check (a cardinal rule when using mechs, a DGI for any mod).

The high center build I pictured above on the Woodvil/Nuppin' was pushing the envelop because for the best results the coil had to be as close as possible to the top cap without touching it and creating a short. Why I mostly used this build in my black Nuppin's that had custom Delrin Syner drip tips that protruded a little down into the atty's chamber. It's Delrin served as a 'height stop gage' to get the coil as high as possible without touching the top cap.

Another build I did that 'flirted with danger' was a quad build in a very small space surrounded on all sides by a very close possible short. This one is on a Geekvape Avocado Genesis 22mm RDTA (pictured here on a TC mod) that I mostly ran on Noisy Cricket mech's, a well known dangerous mech mod. Both of mine had the Fat Daddy Kit in them that made them far safer.

View attachment 902885

I still have my Avocados (22 and 24mm) and this is giving me some inspiration.... I love flirting with disaster.

 

[Spydro]

I still have my Avocados (22 and 24mm) and this is giving me some inspiration.... I love flirting with disaster.

I still have all my Avacado's as well, three 22's (2 SS, 1 black) and three 24's (2 black, 1 SS). For a fairly long time they were among my favorite atty's of all time. But around 2.5 years ago the mesh RDA's and RTA's pretty much retired them and all of the other atty's I had ever used. I ran the 'cados on tube mech's and TC mods mostly, and especially liked the combo with them on Eleaf Pico's, Minikin 150's, a Minikin VGOD 120, and on a VGOD mech.


The quad build was not really a danger, I made sure they could not short out. The flirting with danger (if any) was the Noisy Crickets that could have a mind of their own sometimes.

 

[Skeebo]

The quad build was not really a danger, I made sure they could not short out. The flirting with danger (if any) was the Noisy Crickets that could have a mind of their own sometimes.

I know, I was purely being sarcastic. I do appreciate the post though because I will definitely try this myself... How does it vape? The last quad build I tried made me feel like it was injecting the vapor into my lungs.

 

[Spydro]

I know, I was purely being sarcastic. I do appreciate the post though because I will definitely try this myself... How does it vape? The last quad build I tried made me feel like it was injecting the vapor into my lungs.

How it vapes will depend on a lot of things, like what the build nets in ohms, the voltage/wattage/temperature it is ran at, your style of vaping, etc. My build was a fire breathing lion on a 8.4v mech, but could be a ..... cat on a regulated mod at much lower voltage/wattage/etc.