Stealth vaping cuteness
- Thread starter Giraut
- Start date
- th_trl_thread_readers 0
- Status
I ordered one from FT this afternoon. Will report back about the firing button when it arrives.
That is very cool. I want one! 
Along with an actual eGo kit, since I know my Halo Triton is only "almost" eGo-threaded.
Along with an actual eGo kit, since I know my Halo Triton is only "almost" eGo-threaded. There's about a quarter turn of "impossible positions" so to speak - where the button ends up facing the clearo. If you want to tighten the battery all the way, you need luck if you want the button to end up at noon, 3 o'clock or 6 o'clock. Otherwise you need to back off a bit to reach the previous best position and still keep the battery tight enough to make contact properly. Fortunately, proper contact seems to happen for over 2 turns, so that's not critical, but the battery does have a tiny bit of play in the socket.
If you really want to get rid of it, you could either install a shim between the top of the socket and the battery, stick a layer of scotch tape on the eGo thread to fill the void, file down the socket slightly, or make some kind of clip to connect the clearo and the battery mechanically at the top. But there isn't enough play to bother really.
As for me, I intend to use the thing inside a tin, so I won't see the play even if it bothered me.
Ok, I gotta ask. How the heck did you do that during a meeting? Large or small venue? I would think everyone would see the vapor.
Smaller drags and holding it in longer I would assume. That's how I do it at work when the higher ups are around my work area.
You can take as long a drag as you want, that's no problem. The tricks are:
- Release the button half a second and draw air before removing the drip tip from your lips, to prevent any stray vapor from escaping
- Hold it in your lungs for as long as possible, so the glycerin condenses, and exhale slowly (I suppose it works with PG-based liquids too, but I haven't tried. I only vape VG)
There's also a way to hold it inside your hand and pressing on the button with your ring finger, so the e-cig isn't visible from the outside. That and you need to adopt a Rodin Thinker pose when you bring your hand to your mouth, so it looks like you're lost in deep thoughts or something.
I can vape sitting next to someone and the person would never know.
eGo Mini x 15mm IBTanked HalfLing
...looking forward to see how much smaller this thing can get.
...looking forward to see how much smaller this thing can get.
I found a tin box that's barely bigger than the battery, clearo and U-stand. Check this out:
Now that's stealth!
Here's how it all fits inside:
The foam block comes from an old iClear30 case. I knew keeping these things would come in handy some day
Now that's stealth!
Here's how it all fits inside:
The foam block comes from an old iClear30 case. I knew keeping these things would come in handy some day
If it doesn't line up correctly you can just use a simple rubber washer on the threads and it will change where the button lands when torqued down.
eGo Mini x 15mm IBTanked HalfLing
...looking forward to see how much smaller this thing can get.
Oh my, yet another shiny thing I want ...
Oh my, yet another shiny thing I want ...
Yeah no kidding. It's a great little thing! I'd be concerned about breaking it in my pocket though...
I'd make it a velvet or sequinned carry pouch (hey, I'm a girl I'm allowed to have those kinda things).
You couldn't find a better battery than a Trustfire? Never trust a battery with "FIRE" in its name.
the tank itself with thick walled glass and rubber washers is incredibly strong and break resistant. if anything, the eGo will break way before the IBTanked.
so where do you buy one of those, did you put that together from parts or what? i look for a halfling and it looks like they're $4, but is that just the glass or what? im totally interested in how to get one going.
I was more thinking about the 510 threads. The only connection between the top and the bottom is that fragile little connector - and the tank's bottom isn't pressed firmly against the cone ring to stabilize and solidify the whole assembly, like a one-piece 22 mm clearo base is.
- Status
Similar threads
