Ah, that's nice. Actually, with P3 inside Ody, you may also recicle the "chimney" moutpiece for the obsolete 510 atomizer. (You must remove the inside reduction tube to fit P3)
Sugestions and Ideas for new GG parts !
- Thread starter D Stanley Querfurth
- Start date
- th_trl_thread_readers 0
- Status
I knew that someday we would find a good use for that mouthpiece.
Otello, our meccano guy found it.
Eh Eh, Stan is the Master, I'm only his humble apprentice,
Otello is the official new GG Master of compatibility
i am in double retirement1. ...... stoped vaping
2. because imeo stopped producing non res- res - non res wire * ceramic atty´s...i only had one penny v3..and it was transformed with ithaka old rebuildable at least...so i retired together with the non res wire+ceramic style atty´s
Last edited:
Ariel,
may I suggest to modify the Wiki about the hybrid base?
As I discovered few minutes ago, before screwing the rebuildable part on the hybrid base, you have to remove the center post extension.
Ariel,
may I suggest to modify the Wiki about the hybrid base?
As I discovered few minutes ago, before screwing the rebuildable part on the hybrid base, you have to remove the center post extension.
Of course, any suggestion and help is very appreciated
Let me see if I understood what you mean:
you have to remove the center post extension (used for the 510 base) from the rebuildable part and replace it with the center post extension of the hybrid base.
Something like this? :
1.- Unscrew the Tilemahos rebuildable assembly from the 510 base.
2.- Replace the center post with the one included with the hybrid base.
3.- Screw the hybrid base to Esterigon.
4.- Screw the rebuildable part until it stops.
5.- Assemble Tilemahos as usual.
No Ariel, you only have to remove the post extension.
There's no center pin included with the hybrid base, or better: it is fixed to the bottom of hybrid base, so when you screw the rebuildable part, you screw the center post, too.
There's no center pin included with the hybrid base, or better: it is fixed to the bottom of hybrid base, so when you screw the rebuildable part, you screw the center post, too.
I'm lost, sorry
On Tilemahos v1 you have to remove the center post (of both versions 510 and AD bases) and use the one that comes with the hybrid base, the center post is not fixed into it, of course, you can leave it in the hybrid base and screw the rebuildable part, but it is easier if you remove the center post and screw it on the rebuildable assembly before screwing it in the hybrid base.
Or, you mean the center post extension of the "Update Ad pin + Center post Extension for Tilemahos V1"? (and / or the one that comes with Tilemahos v2 21mm)?
Ah, OK, you're right, it's possible to remove the pin from the hybrid base.
Mine was very hard to remove, so I imagined it was fixed.
Mine was very hard to remove, so I imagined it was fixed.
Please Guys, be patient with an old man who falters
Fact is, of course I didn't know the hybrid base video, but I did see the one on T. 2; I mean, I was aware of the sealed pin remaining locked in the base!
But the pin in the hybrid base was really locked, it didn't move; at the end I tried to screw the rebuidable and it worked.
Imeo - is it possible we could have some GG4S buttons with the wings engraving facing up when the mod is standing up?
I do understand why they were made the other way, but I would really like it if the wings were upright when my GG4S was upright.
Thanks for your consideration.
I do understand why they were made the other way, but I would really like it if the wings were upright when my GG4S was upright.
Thanks for your consideration.
This isnt really possible Big because all GG4S are already made. Maybe later when I will run out of stock I can make buttons like this
I second that brem.. The PenelopeV1 is still my weapon of choice..
My only other wish would be for an 8mm one piece mouthpiece for Tilemahos V2 (with a new top cap)
any thoughts about a solid tube for 18500, imeo?
that would nicely close the gap.
yes i know, i can built it with my just gg, but it would be nice to have it as a solid tube....please
that would nicely close the gap.
yes i know, i can built it with my just gg, but it would be nice to have it as a solid tube....please
I just checked Brem and solid 18650 tubes were not on preorders. If they were on preorders then it t would be easy to make 18500 too at the same time. But starting a new item on a cnc machine requires time that we dont have right now
- Status
