Suggestions for mech mod

[Kozmic]

I'm new to this site, but not to using APVs etc. I've been doing quite a bit of research before I jump into modding and rebuilding atomizers. My top choice rda is currently the plume veil. I was wondering what you all thought would be a solid choice of providing the power. Should I go regulated box mod like cana modz or get a mech mod like perhaps a pegasus clone; or neither? I'm open to the mods, I'm just sold on the plume veil rda.

Thanks

 

[v1k1ng1001]

Get both. I've seen decent mech clones for $10-$25--they can serve as back ups or pair them with a kayfun in 18350 mode for a pocketable vape.

Looks like a nice rda!

 

[Kozmic]

Alright cool, that seems reasonable. If you don't mind, could you point me in the direction of where to pick up some reputable clones. Also I have a question about batteries. I feel that the sony vtc5 is a good choice, but I was unsure of when to take it out and recharge. Should I let it discharge to around 3.4-3.3 volts or should it be switched out even sooner than that?

 

[Mikokawibawa]

I think Mechmod looks just great (got a nemie)... But i guess regulated mod is more convenient.. Don't have to check ur voltage every now and then... I say.. Go with Hannamodz 30w or IPV v3 50w


miko

 

[lownote2]

I've been looking at the same things. vaporshark looks good, but the battery is smaller. hana gets a lot of raves. I'm really interested in dovpo's new e-mech. That looks amazing, but there's not a lot of reviews yet even though the one's out there are good. I've got my trusty MVP 2.0 and a Magneto. I really liked the Magneto for awhile, but there just seems to be something better about the regulated mods. I'm thinking it's the full power all the time instead of dealing with the battery drain.

In answer to the OP, I usually charged mine when it hit about the 3.7 range. I know you can go lower, that's just me. Don't let it get too low or you can damage the battery. (so I've heard anyway) I wouldn't let it get to 3.3 personally, maybe 3.5. But I'm not a pro, still new, so take my advice with that knowledge.

 

[Kozmic]

In answer to the OP, I usually charged mine when it hit about the 3.7 range. I know you can go lower, that's just me. Don't let it get too low or you can damage the battery. (so I've heard anyway) I wouldn't let it get to 3.3 personally, maybe 3.5. But I'm not a pro, still new, so take my advice with that knowledge.

Okay thank you! I just thought the batteries were safe to discharge a bit more, but I'd definitely rather be safe than ruin my batteries or have one of them fail and damage my device. I'll definitely keep this in mind.
Thanks again.

 

[Newportlocal]

I've been looking at the same things. vaporshark looks good, but the battery is smaller. hana gets a lot of raves. I'm really interested in dovpo's new e-mech. That looks amazing, but there's not a lot of reviews yet even though the one's out there are good. I've got my trusty MVP 2.0 and a Magneto. I really liked the Magneto for awhile, but there just seems to be something better about the regulated mods. I'm thinking it's the full power all the time instead of dealing with the battery drain.

In answer to the OP, I usually charged mine when it hit about the 3.7 range. I know you can go lower, that's just me. Don't let it get too low or you can damage the battery. (so I've heard anyway) I wouldn't let it get to 3.3 personally, maybe 3.5. But I'm not a pro, still new, so take my advice with that knowledge.

I enjoy my stainless telescoping magneto. I agree I prefer regulated mods. My Provari has too high a low ohm setting for my taste. My Cloupor DNA goes down to .5 which is better. Plus the 30 watts of power. One Vaporshark actually can come with a bigger 18650 battery. The RDNA. I am considering one. I prefer it to the other ones. I would rather easily change out my battery than send the other models in when the battery gets old.
Vapor Shark rDNA