Super Noob Super Confused

[lefty23]

Hi all. So, until now I have been using a basic ego battery. I just got my vamo in the mail today, and of course had to break it right out for a test spin. I am using a kanger pro tank with it, and the vamo lcd says the ohm resistance is at 2.5, which would make sense. The card that came with the pro tank recommends 3.9V-4.2V for a resistance rating of 2.5. Now the strange part: at the very lowest setting (3V), it seems to hit fine, but anywhere above 3.3V or so and the hit tastes extremely burnt instantly. Like really bad. What the heck am I doing wrong? Thanks for your help, I am really confused here.

 

[DaxFX]

You need to change your settings from avarage mode that is the factory preset. Press and hold any of the small butons for 10 seconds untill display say NO2.


Sent from my iPhone using Tapatalk

 

[lefty23]

I figured it would be something simple like that-- thank you so much, I really appreciate it.

 

[DaxFX]

Enjoy your new vamo


Sent from my iPhone using Tapatalk

 

[lefty23]

I am definitely enjoying it already now that I have the right setting. Are there any particular tanks or attys that you would recommend for use with it?

 

[DaxFX]

That depends on what you liked,, almost everything work perfect,, the most one im using are the EVOD exellent vape, and the smok RDA octopus dripper, i ordered the cobra clone from fasttech but i blow the coil in my firs try but the cobra so far looks awesome.

Smoktech RDA

Metal vision vivi nova

EVOD

Fasttech cobra clone

Sent from my iVap using Tapatalk HD

 

[rushman]

I dropped mine at one point and somehow it reset it, I fried 2 protank heads before I realized what was going on (average instead of RMS mode).... now I check to make sure at the first sign of a burned hit.

 

[lefty23]

Cool, thanks for all the solid info everyone.

 

[stealthmayhem]

Now I am being a super noob, but what is the setup on the right.....the black one?

 

[Leoleoleo]

Now I am being a super noob, but what is the setup on the right.....the black one?

If I'm looking where you're looking, that's an evod on an evic.

 

[tddman66]

Hi all. So, until now I have been using a basic ego battery. I just got my vamo in the mail today, and of course had to break it right out for a test spin. I am using a kanger pro tank with it, and the vamo lcd says the ohm resistance is at 2.5, which would make sense. The card that came with the pro tank recommends 3.9V-4.2V for a resistance rating of 2.5. Now the strange part: at the very lowest setting (3V), it seems to hit fine, but anywhere above 3.3V or so and the hit tastes extremely burnt instantly. Like really bad. What the heck am I doing wrong? Thanks for your help, I am really confused here.

Forget volts and use the better power setting.... With the Vamo you can set the watts.... It will deliver a much more consistent vape. Most find between 6-8watts to be the sweet spot. Hold both adjustment buttons down to switch from volts to watts. W in upper right corner= watts. V right side center=Volts. Once you set the watts you will find much less need to fiddle with settings. I find 7 watts works pretty good on just about everything.

Hold down the right side adjustment button until it reads No1 or No2.... If it shows No2 you are good.... If it shows No1 do it again and it will now show No2 RMS mode.

If you still have burning you need to get your hands on a meter and check the volts at the 510 connection. Make sure it is firing the same voltage as you have it set up to deliver.

 

[stealthmayhem]

If I'm looking where you're looking, that's an evod on an evic.

Yep, that was it.........I know what I want for Father's Day. I was looking at a ZMax, but that thing looks nice.

 

[Leoleoleo]

I might be wrong but I think you will have to get the black tube sparately. They're not expensive but not everywhere sells them. It also looks like a chrome finished cone on the top there which would also be an additional purchase. The default finish as shipped is a kind of satiny aluminium.

 

[jonescreek]

evic on the right...