Tesla Invader III
- Thread starter Winchester
- Start date
- th_trl_thread_readers 0
- Status
I want to know this as well. I've got a bunch of other mods - regulated and mech. After playing around with TC with nickel, titanium, and SS I always seem to come back to regular Kanthal for ease of use and dry burning. I don't vape over 40 watts but a dual 18650 mod with just a simple "start low and turn the dial until you hit the vapor/heat that you like" is very appealing.
I ordered one I'll let you know when I get it. I think it is going to be just like my Hex Ohm V2. We will see! I still use Kanthal wire and I run at about 35Watts.
Pretty happy with mine. The fire button can be (tesla typical) a pain when not properly pushed (misfires)
Battery life is really good.
Battery life is really good.
I have two and had life not stepped on my plans I would've bought more. As mentioned battery life has been killer on it. I have had similar things with the button as daisychainvaper mentioned. Occasionally when pressed it doesnt fire but it's a rare occurrence with either of them.
One thing to mention on them, the battery under the atty shares the spring with 510 pin. Unscrew the atty a few turns and save your wrappers. I dont always do that when I'm in a hurry but try to most of them time. A pic of the guts incase anyone is curious.
One thing to mention on them, the battery under the atty shares the spring with 510 pin. Unscrew the atty a few turns and save your wrappers. I dont always do that when I'm in a hurry but try to most of them time. A pic of the guts incase anyone is curious.
Just received my Tesla Invader 3 and I'm really liking this box mod. Easy Peasy. It seems solid and well built.
All other mods have been put on the shelf for now. The only improvement I would make would be to install a 2 amp internal charging board - something like the Sigelei 213 or the Dna - my favorite feature of my Vaporshark rDna40.
All other mods have been put on the shelf for now. The only improvement I would make would be to install a 2 amp internal charging board - something like the Sigelei 213 or the Dna - my favorite feature of my Vaporshark rDna40.
I just got my Tesla Invader 3 today. I like it very much it's very simple and easy to set to taste. Looks like it may hold up for a long time. Not digging the clear coat on the silver but, it is better than the black. I hear it comes off right away.
I love mine and I can attest to the quality of this box im a heavy equipment operator and this thing can take a beating and work great no problems at all really haven't had a problem like the others with the fire button though
Having problems with mine.
It just stopped working.
Blinks 5 times everytime i try to fire it.
No atomizer short.
Doesnt work on.19 ohm atty
Doesn't work on.33 ohm atty.
I did not drop it nor has it been wet.
It just stopped working
Help!
It just stopped working.
Blinks 5 times everytime i try to fire it.
No atomizer short.
Doesnt work on.19 ohm atty
Doesn't work on.33 ohm atty.
I did not drop it nor has it been wet.
It just stopped working
Help!
Have you check your batteries? In properly? Do you have another set of fully charged batts to try?
Yeah man.
Low batt flashes 15 times then turns the mod off.
Mine blinks 5 times then standby mode. Manual says it's either a short or high amp warning.
But im at a .33 ohms and no short as the same atty and build works fine on my eleaf tc100w. Even my other attys with different builds.
Low batt flashes 15 times then turns the mod off.
Mine blinks 5 times then standby mode. Manual says it's either a short or high amp warning.
But im at a .33 ohms and no short as the same atty and build works fine on my eleaf tc100w. Even my other attys with different builds.
No fix man. Asked more around and a lot of the tesla invader iiis has chip problems.
Sucks coz i like it si much. Changing to the noisy cricket 2 instead.
try what i did with it...
adjust the bolt inside just below the pin the one with the riggid thing around it...
turn it to the right as tightly as possible...
then make a simple build perhaps aroung .5 ohms then test fire it to the lowest setting of the turn knob...
hope it helps...
- Status
