Have you tried Lighthound or RTD Vapor they may be able to help you? Where are you located?
- Status
Have you tried Lighthound or RTD Vapor they may be able to help you? Where are you located?
man I'm the same with my bottom feeders, once you find bottom feeding it's hard to really enjoy anything else, other stuff can be ok or even kinda good, but for me BF is just the best, I'm always trying to think of ways to bottom feed everything, would love to figure out a way to BF my rose atty 
here's my 1/2 in 1/2 out atty setup I came up with to BF my billetbox bvc's are really really good, but nuppin' is better
here's my 1/2 in 1/2 out atty setup I came up with to BF my billetbox bvc's are really really good, but nuppin' is better
lighthound did not ship outside of US.
RTD vapor shipping cost is waaaayyyyy too high mate.
im from malaysia.
Greeting, "Don" Corleone. Does RTD Vapor not ship to Malaysia? They may not but I have to ask. They do have them in stock.
AW icr 123 16340 protected battery - RTD vapor
If the chemistry is the same I would expect others to work, but I'm far from a battery expert. If you have something specific in mind, it might help to post the details, so those who ARE in the know can answer you with more confidence than I can.
Congratulations on your new BB!
Strike my last question (RTD) and I'm sorry to hear that.
Some vendors in my country advise to try using the efest 16340 (3.7v) and KeepPower CR123 / 16340 3.7V 700mAh Protected Li-ion Recharge Battery. Has anyone had any experience using both of this brands?
Im really excited to get my kuerbiskuchen bb tomorrow!!!
Im really excited to get my kuerbiskuchen bb tomorrow!!!
I lost one of the parts to my billet bridge.
Surely it was the little piece. I've been nervous about doing this myself and am always overly careful. It was either Peter_C or Tele67 who dropped theirs down the drain, but the lovely Bamrz came to their rescue (if I recall) and got an extra piece shipped from Atmistique.
I don't know if DD has any individual parts, but it might be worth the asking. Sorry for your loss :-(
I lost one of the parts to my billet bridge.
Oh bummer, cat2! Here, let's sing. Maybe that will make you feel better.
Order them and have them shipped to me and I will ship them to you.
I lost one of the parts to my billet bridge.
This happened to me some months back. A wonderful ECF friend was kind enough to find that (tiny) part for me. Point is I do feel for you~! If you email the maker, you *might* be able to get just the lost part...
It was dem fairies I tell you~! It was not down the sink (I work in a bowl only for that reason) - it just *POOFED*! and gone... And, because I was not a paying customer, I did not feel it would be right of me to impose upon the wonderful people at Atmistique.
*HUGS* Bamrz
I lost one of the parts to my billet bridge.
I just recently started using a Billet Bridge, so I'm not TOO familiar with them, but based on looking over the DIY Billet Bridge instructions I may have an idea for replacing the bottom trim piece of a real-deal Billet Bridge.
What I'm thinking is that if you have a spare 510 extender and a Dremel tool or something else to cut/grind with, you should be able to cut off the bottom/threaded part of the extender to make what is basically a 510-threaded ring, that should be able to replace the bottom part of the Billet Bridge (and would be open enough that the pin of the BVC atomizer can be left as-is).
Might be something that'd work in a pinch, anyway....
I thought or suggesting that but there's no telling if the diameter is going to be correct.
I don't mean the threads I mean the diameter that fits into the o ring in the tank. Does it fit well?
I lost one of the parts to my billet bridge.
If you have a Sabot DDD, that bottom piece will work in place of your lost piece..
- Status
Similar threads
