- Status
Cannot wait for the BBs to go on sale. I've been stalking the BB home page and this thread every day!! Hopefully when the orders start going out there will be some up for regular purchase as well.
A little off topic but regarding the 16340 chargers. It seems like the general consensus is the nitecore i2 or i4 intellicharger. Has anyone tried the XTAR VP1?? I know it only has 2 bays and costs a little more, but my concern is the safest possible way to charge batteries. Being able to select the charge current as an option is attractive (as well as the pretty LCD screen of course 
). Has anyone used the VP1 before??
Thanks
). Has anyone used the VP1 before??Thanks
A little off topic but regarding the 16340 chargers. It seems like the general consensus is the nitecore i2 or i4 intellicharger. Has anyone tried the XTAR VP1?? I know it only has 2 bays and costs a little more, but my concern is the safest possible way to charge batteries. Being able to select the charge current as an option is attractive (as well as the pretty LCD screen of course
Thanks
Yup I've got 1 and it works like a dream.
edit: howdy from edmonton
Yup I've got 1 and it works like a dream.
edit: howdy from edmonton
Howdy fellow Edmontonian, haha.
Roughly how long do the 16340s take to charge on the VP1??
Really?? That can't be at a charge rate 250? Or are you bumping it to 500ma?
I charge all my batts at 250 because its better to charge slow and steady than fast. Max 45 min to charge the cr123
Wow that's surprising. I expected a charge time more in the ballpark of 2-3 hours. A 2 bay charger suddenly doesn't sound bad at all. That's awesome, thanks for the info bk78!
I have a Xtar Vp1 and I4 with Efest battery (I do not like them)not in the BB
it went down to 2.5 volt I4 could not recharge the voltage too low I think . xtar vp1 recharge the battery no problem
both are good but I prefer the VP1
it went down to 2.5 volt I4 could not recharge the voltage too low I think . xtar vp1 recharge the battery no problem
both are good but I prefer the VP1
Can anyone show me what replacement o-rings I need to order for the tank? I kinda ended up shredding the bottom one up just now... :/
Oh, and i've concluded that my tank leaks from the top somewhere. meh.
Oh, and i've concluded that my tank leaks from the top somewhere. meh.
Should just be a standard o-ring. Inner diameter 9mm with a thickness of 1.5mm. Hope this helps!
I buy this o-ring but I'm not sure if is the right o-ring for tank, the size look good but the Nitrile Rubber(NBR) dont know if we need silicon o-ring
12mmx9mmx1 5mm Autos Seal NBR O Rings Gaskets Washers x 50 | eBay
Free shipping
Last edited:
Thanks guys, really helps!
rcoute, those rings fit and work well in your BB?
I wonder if there's a more durable material out there that we can use, something that won't get sliced up so easily. Any ideas?
rcoute, those rings fit and work well in your BB?
I wonder if there's a more durable material out there that we can use, something that won't get sliced up so easily. Any ideas?
I did not try yet because I do not know same size , Nitrile Rubber(NBR) Features high and low temperature resistance, are they good ?
Same place i bought those needle work perfect
100 PCS Industrial 0 58mm Inner DIA TIP 20ga Dispensing Needles Pink | eBay
I think a tougher material may make it more difficult to insert the carto. A more heat resistant material would be interesting though as I hear after quite a bit of use the lower o-ring tends to hold onto the carto.
Do we need silicone o-ring or if Nitrile Rubber(NBR) do the job that my question ? not sure
Last edited:
Punched my first carto today...in preparation for those 2nd rounders...haven't vaped from carto in a while...pretty much only use them when tasting juices in store...not bad, but much louder than I remember
- Status
Similar threads
