The Fusion Tank!

[mwa102464]

nice..I tried but I couldn't get a carto thru the end caps..lol

Deb I don't see that as being a problem, they are all mostly the same size as a CE2 Sleeve, I think they are 9mm, try putting a little water around the inside of the hole, just wet it lightly and push, I want to say an old saying but will refrain from doing so but it will go Deb

 

[debb]

Deb I don't see that as being a problem, they are all mostly the same size as a CE2 Sleeve, I think they are 9mm, try putting a little water around the inside of the hole, just wet it lightly and push, I want to say an old saying but will refrain from doing so but it will go Deb

thanks..will give it another go..

 

[5cardstud]

Well here is the last one I'm building until I build my own from a tank I make. This is the Fusion MAP tank and it is also the best performing cartomizer I've used in the MAP tank including the E2 or CE2 or the xyz2. I had to use one of the drip tips off the 510 drip tip carto to extend the Fusion just a tad but there are no leaks. I cut the very end off the drip tip, chucked it up in my drill , then I used my Dremmel and with both turning I put a groove in the end I cut off so I could put an O-ring on it. Now it had an O-ring on both ends and it worked perfect.
This baby just rocks FUSION style.

 

[mwa102464]

5Card are you having to drill or make a slit in the Fusion or are the little air intake holes on the bottom of the fusion sucking the juice up into the carto for you on this tank.

 

[5cardstud]

Oh! Don't worry I am a fangirl as well. I just obtained an order about an hour ago. I ordered LR Fusions (excited to try these) and his dual coils. I have never been disappointed. The quality shows...I am just intrigued by you tank. I have a SSR tank and I am trying to figure out if I can adapt it. I might have to start from scratch.

It should work fine.

5Card are you having to drill or make a slit in the Fusion or are the little air intake holes on the bottom of the fusion sucking the juice up into the carto for you on this tank.

I'm using my Dremmel to cut a small slit just above the lower seal. You have to keep the air holes open for draw.

 

[5cardstud]

5Card are you having to drill or make a slit in the Fusion or are the little air intake holes on the bottom of the fusion sucking the juice up into the carto for you on this tank.

Here is how I did it.

 

[debb]

you do one slot or two?

 

[5cardstud]

you do one slot or two?

I just do one small one. Sorry this is a cheapo camera. makes it look like it has moss growing in the bottom of the tank.

 

[debb]

cool, thanks..

 

[Sdh]

Nice! Oh and a big he haw as well!

 

[5cardstud]

Nice! Oh and a big he haw as well!

Thank you Sdh.

Update: After using this today it seems to have broke in or something but it is just perfect. I really love this fusion in the MAP tank and it has moved into the #1 spot for me. I'm happy about another thing. I'm finally getting some use out of this MAP tank. It has sat here forever because I didn't care for it with the E2 in it. This thing rocks and NO LEAKS. Woo Hoo.... oh sorry I mean YEEEEEEEEEEEEEEEEEEE Haw.

 

[mistinthewoods]

Hi all. I've been rockin' this Liquinator tank with a Fusion in it all week out here on the beautiful Oregon coast and in Portland. I have been having to refill it in the middle of the day but that's still pretty convenient. No leaking and the length of this tank is nearly perfect for the Fusion. I may need a few more of these tanks.

 

[5cardstud]

Hi all. I've been rockin' this Liquinator tank with a Fusion in it all week out here on the beautiful Oregon coast and in Portland. I have been having to refill it in the middle of the day but that's still pretty convenient. No leaking and the length of this tank is nearly perfect for the Fusion. I may need a few more of these tanks.

Cool Mist. I've been filling this Map/Fusion once a day. I rebuilt my other tank and there is no stormy tank left to it. It holds around 4.5 ml.
These tanks are the way to go. Well if you have a Fusion or another Ikenvape carto to put in them but nothing beats the Fusion.

 

[Chingas]

5C, I have an old MAP tank collecting dust and have been trying to get a Fusion into it. Not having any luck. Any trick to it? Did you bevel the outside of the bottom delrin cap or the tip of the carto to get it in?

 

[debb]

i beveled mine out...BE CAREFUL! on one of mine I went too far...its easy to do....so I didn't bevel my other tank out ..got it all together and it leaks thru the batt end of atty,..still working on it tho....hope I get working right....

btw..I used a hammer and tapped mine in...everything went well til I filled it...lol...my first tank is working...but my second is the one leaking...

 

[5cardstud]

5C, I have an old MAP tank collecting dust and have been trying to get a Fusion into it. Not having any luck. Any trick to it? Did you bevel the outside of the bottom delrin cap or the tip of the carto to get it in?

No that part has to stay below to get the draw. I took one of Ikens metal drip tips off the 510 v2 drip tip carttomizer, cut the lip off the mouthpiece end of it. Then put it in my drill and turned it while using my Dremmel to make a groove in it to put an o-rins on each end. It seals in the Fusion and the top Delrin. I can turn it in any position and no leaks.

 

[debb]

how far up does the extension go...do you put the dt into the extension?...nice work, btw....I am just winging it..

 

[5cardstud]

It fits in the carto like a drip tip and goes into the Delrin about a 1/4 of an inch. The o-ring on both ends seals it well.

 

[debb]

awesome..thanks!

 

[5cardstud]

I can't figure out where that picture went but it's gone. I think it was this one, Sorry.