Wicked/coiled/filled again and my Vanilla Cream is the chit....I'm hoping I didn't clean all the machining earl and crud off when I first received. Cross your fingers.....
- Status
Taking off is the same as putting on, except in reverse. Taking off: remove top cap o-ring, turn and pull tank with controlled pull, no force, and it will slide right off. Once clean and dry, lube the o-rings and inside lips of tank and turn and push with controlled pressure. Easy as pie.....
Thanks crypto, I didn't think it would be terrible but I know some people have cracked theirs. Unfortunately face was out of extras when I snagged a iHybrid so I figured I'd ask before an attempt in case their was a trick.
So today the mailman dropped a package on my door from Greece. I opened it put it together and used one of the wicks that was shorting out in my ihybrid. It is working perfectly.
I dont know what to do. Try an isolater or start drilling to make the hole bigger.
Feels like my tech support days. Swap with a known-good then what?
Sent from my Epic using Tapatalk
I dont know what to do. Try an isolater or start drilling to make the hole bigger.
Feels like my tech support days. Swap with a known-good then what?
Sent from my Epic using Tapatalk
Try the cig paper technique but use more paper so it extends into the tank top.
Another member suggested using cotton to insulate the wick.
Hope it works out for you! What mod did you get?
Unfortunately it's still probably the wick. If you got a rebuildable genesis from greece I know what you have and it also has a bare stainless hole so it would seem that the problem would be with the iHybrid. BUT I would say the odds of that being the case are very astronomical.
When you took your wick out of the hybrid and put it into the DID you aren't going to have exactly the same points of contact in regards to where the wick passes through into the juice tank. SS wick shorting spots are tiny. You won't even be able to see them on the actual wick but it sounds like you have one.
You could use an insulator as that will completely stop the wick from shorting when it passes through the tank or you could re-make your wick. You could also move the wick way out of the hole and wrap a coil to see if it's shorting. Although I know this won't be a functional setup you could see if it does the same thing when you wrap a different part of the wick.
When you took your wick out of the hybrid and put it into the DID you aren't going to have exactly the same points of contact in regards to where the wick passes through into the juice tank. SS wick shorting spots are tiny. You won't even be able to see them on the actual wick but it sounds like you have one.
You could use an insulator as that will completely stop the wick from shorting when it passes through the tank or you could re-make your wick. You could also move the wick way out of the hole and wrap a coil to see if it's shorting. Although I know this won't be a functional setup you could see if it does the same thing when you wrap a different part of the wick.
Great advice,
I myself have both the ihybrid and the did.
The part of the wick that sticks out of the did is shorter.
So I'm pretty sure you're touching the body at different points.
Sent from my Galaxy Nexus using Tapatalk 2
Is it possible to get another cap that is straight for those of us with crooked ones?
And the small amount of juice inside the sleeve is not a deal breaker for me.
I still feel it will clear up with a straight cap.
Still lovin' my iHybrid!
And the small amount of juice inside the sleeve is not a deal breaker for me.
I still feel it will clear up with a straight cap.
Still lovin' my iHybrid!
All I see in that picture is a Pluid. Why is it so greeeeeen?
That condensation is driving me nuts!! I have fixed it, I think, I'm on day 2 with no condensation around tank sleeve, I'll keep yall posted, There is no leaking, its just condensation. Also, I test all the top caps, when you press it on it could be rising a bit, when you put it on, look where your air hole is and twist it from left to right so it locks in place, it should be straight.
They are custom made, you would have to get one from me, its going to really hard to get the old one out though, they are compressed in there for a snug fit.
See above
I think I have figured it out Very very easy to make it stop, I'm making sure its working though, it has to do with the tank, not the unit itself.Hey all been a long weekend for me. Work was crazy
Wanna say happy belated birthday faceless and don't wear yourself out. In my experience when that happens work and the quality of it will suffer. You created a fine ATV here and I'm sure you wouldn't what its quality too decrease. Plus as always family definitely comes first.
Also Wanted to know if there was also any update on the colors? And it was a possibility of getting a green 1
《Sent from my handheld information procuring fruit ninja》
20 complete red
20 complete black
10 complete green
those will be available by weeks end
Completely disassembled my iHybrid and cleaned with Dawn, and then 91% iso alcohol, no smell out of the batt tube or the switch but the top cap and the atty assembly give me an odor. I had an aluminum Ridgemont DT on when I first got the iHybrid and filled with Vanilla Cream from COV, tasted great for the first day then started getting a strange taste, pulled off the aluminum DT and put on a Trippy and it stayed the same. After the cleaning and letting dry I still smell the metallic odor, does anyone else get this? I put mine in storage in my PV caddy for the time being, if I can smell and taste, I worry a bit plus it's not pleasant.
I try and clean them the best I can, its probably the machine oil you smell. I used dawn dish soap and washed them. I used denatured alcohol on mine but didnt want to do that with everyone elses for health purposes. Thats why you smell it in the bottom, its the SS also from the top part. The aluminum will not smell like that because I did clean the parts that don't come into contact with juice with denatured alcohol. I would put that top part in the dishwasher. Its all SS even the screws except one , the brass one.
He is, I scrapped the first one because it was the prototype, his pluid edition will be shipped friday with special engravings
How's mine looking Face?
lol I hope you don't mind being called "Face"? Wasn't Jason Statham's character in the Italian Job named "Face"? Maybe that's why I like the ring of it
lol I hope you don't mind being called "Face"? Wasn't Jason Statham's character in the Italian Job named "Face"? Maybe that's why I like the ring of it
Oh.....20 complete black......
The best looking ones will be purple and turquoise....I won't use purple because its too feminine for me lol, but that turquoise is sick looking!! They will be ready next week
How's mine looking Face?
lol I hope you don't mind being called "Face"? Wasn't Jason Statham's character in the Italian Job named "Face"? Maybe that's why I like the ring of it
edit,....Lol no! It was the guy in A Team
How's mine looking Face?
lol I hope you don't mind being called "Face"? Wasn't Jason Statham's character in the Italian Job named "Face"? Maybe that's why I like the ring of it
Yours ships in the morning
Its looking good too lol, just don't call me Engelbert- Status
Similar threads
- Locked
