- Status
My 91% arrived a week ago today. I had been running a Kanger Pro because I gave up on the AgaT-2 and I absolutely hate my Z-Atty-Pro because of the huge air hole. Yes I am a Provari user. I was able to order one from Elements in San Jose but this was only after searching for three months so I had seen quite a few reviews and watched a bunch of setup videos. I decided I would try my hand at a cotton fiber micro coil using the supplied wire. I built a jig to assist with the coil and made 10 wraps around a 1/16" or so metal rod on my jig. I repeatedly heated the coil with a torch and compressed it with hemostats until all coils were touching. I then installed it in the 91% and it tested at 2.6ohm. I set my voltage at 5.0 and fired it a few times compressing it when it would start to glow with the hemos. The coil was heating from the inside out as they say they are supposed to and visually the coil was perfect. I attribute this to the jig. I have built many normal coils but never one this perfect. Next I tore off a small piece of cotton ball, rolled one end and screwed it into the coil so as not to disturb the coils. After some trimming, final assembly and adding my favorite DIY Apple Tobacco I gave it a vape at 5.0 volts.
Oh my god this thing is good. Good is an understatement. It is fanfriggintastic. Flavor is off the chart. Vapor production is huge. Throat hit is awesome. Never a dry hit or burnt taste. I bumped the voltage down to 4.9 and tightened up the air hole a little and have been using it exclusively since.
The only complaint I have is that it does seem to leak very slightly into the mouthpiece but I think I may not have gotten the "O"ring seated properly on the chimney. a simple cleaning of the area under the mouthpiece every few days seems to do the trick.
My unit is very well made and has no blemishes. I highly recommend the 91% especially for VV users however if your not using a micro coil your results may differ.
Oh my god this thing is good. Good is an understatement. It is fanfriggintastic. Flavor is off the chart. Vapor production is huge. Throat hit is awesome. Never a dry hit or burnt taste. I bumped the voltage down to 4.9 and tightened up the air hole a little and have been using it exclusively since.
The only complaint I have is that it does seem to leak very slightly into the mouthpiece but I think I may not have gotten the "O"ring seated properly on the chimney. a simple cleaning of the area under the mouthpiece every few days seems to do the trick.
My unit is very well made and has no blemishes. I highly recommend the 91% especially for VV users however if your not using a micro coil your results may differ.
Here you go
I like the look of your 91 on top the nemi better than i do my 91 on top my satin ELA,go figure.
I like the look of your 91 on top the nemi better than i do my 91 on top my satin ELA,go figure.
Any pics of your Satin ELA and R91?
I like the look of your 91 on top the nemi better than i do my 91 on top my satin ELA,go figure.
Maybe if you polished your ELA's bling rings....
Sent from my SCH-I405 using Tapatalk 2
No i can't do that i like the satin finish too much.There are only a few of these ELA's with this finish in the wild.I only wish i had purchased an extra set of rings when i purchased my ELA.
Well, close to 3 months have gone by since I started this thread until receiving the R 91%... It really wasn't a bad wait considering the much lower pre-order price, and the fact that they only recently started showing up for sale at retail.
Mine was VERY good.
The finish, fit, threading, and machining all nice. The adjustable 510 pin works great, and would come in handy with fixed-post devices. Kinda sad thing though.. I didn't vape it. Right before I was going to a couple of days ago, I noticed a sweet HANA MODZ Pack V2 DNA20 on the classies. 
From the very limited last run, the member only had it for one day, and decided it wasn't for him.
Long story short, one of the items he considered toward a trade just happened to be the R 91%, and I should be getting the HANA on Saturday.
Mine was VERY good.
The finish, fit, threading, and machining all nice. The adjustable 510 pin works great, and would come in handy with fixed-post devices. Kinda sad thing though.. I didn't vape it. Right before I was going to a couple of days ago, I noticed a sweet HANA MODZ Pack V2 DNA20 on the classies. From the very limited last run, the member only had it for one day, and decided it wasn't for him.Long story short, one of the items he considered toward a trade just happened to be the R 91%, and I should be getting the HANA on Saturday.
I just ordered an R91 from an in stock vendor. I remember seeing in a review (or comparo with KFL) that replacing the adjustable 510 pin with a brass screw could bump performance. Has anyone here done this? And what size would it be?
Wow! that's a really good trade. But the R91% would look good on that Hana.
Here's mine with a Gun Metal Hana Mini.
Looks Great!!
The R 91% was a partial trade along with another item I had. My HANA has a date with the new Rose tank atty by Eden Mods, which will be on it's way soon. Just out of curiosity what ohm reading is everyone getting. I put mine on a ohm meter last night and it did not give a reading. Didn't think about adjusting the center post. I'll give that a try tonight.
Mine came in a few days back. Have one of them at the office today...hanging out with a GUS 18650 and a Turtleship/Lite set up. Mmmm mmm good.
those of us that ordered from vaportekusa are still waiting... i was on the first batch of preorders, 3 months ago. begining to wonder if we'll EVER get them.... kebo must really dislike vaportek lol.
No it's not that,it is because VT pre-sold them for,..what was it,$62.Kebo black flagged all VT orders,all manufacturing,everything stopped for VT until they cleared it all up.The 4-5 week lead time started again from whatever date that was,i forget.
I'm in on that order also. I never thought it would take this long but that's OK. I've got other stuff to keep me busy and it's nice to have something to look forward to.
- Status
Similar threads
