- Status
Hey everyone. After reading most of this thread I ordered my first Vmod 2.0 last Friday. Last night it says it shipped so hopefully I will receive it later this week.
One question. Do the seals come already installed on it or do you have to put them in?
Thanks,
One question. Do the seals come already installed on it or do you have to put them in?
Thanks,
I too jumped on the $4.99 sale for the Vmod 2.0 body cover, but a little late I'm afraid. I was able to order one in Camo, but I really wanted one of the wood grain ones but they were out
Hi everybody! Vapage is going to be on KFI radio tonite, 7:30pm PST. That's 640 AM radio. This is the Tim Conway show!
(Will post this on the other VMOD threads as well.)
Enjoy~
(Will post this on the other VMOD threads as well.)
Enjoy~
I'm pretty sure it's ok, but wanted to double check:
Is it safe to charge AW IMR batteries in the Vapage VMOD charger provided with the premium kit?
Thanks for the help
The simple answer is -- yes.
One can use the same charger for most of the batteries sold by vendors for APV use. These are either High Drain IMR's or Protected Li-ions. The Vapage batteries are Protected li-ions, I do believe.
There are 2 exceptions that I'm aware of --- and almost all vendors will say "Uses XYZ charger only".
Last edited:
Excuse me if this has already been covered here. Can anyone tell me if the "Dripping Atties" from Smartvapes will work on the Vmod? They have a sealed bottom connection so I was not sure if they would work.
Thanks,
Thanks,
"Just for the heck of it I tried a sealed bottom HH.357 atty on the XL...feeds & performs perfectly! " (from the linked thread)
The vmod2 internals are exactly the same as the vmodXL and since the XL was the first vmod to be able to feed just about any 510 atty there is a lot of atty discussion on this thread about attys -- lots!
http://www.e-cigarette-forum.com/fo...d-xl-18650-bottom-feeding-mod-vapage-com.html
You might want to search the thread for more info about the dripping atty's. They do feed -- but I don't know of anyone mostly using them.
The vmod2 internals are exactly the same as the vmodXL and since the XL was the first vmod to be able to feed just about any 510 atty there is a lot of atty discussion on this thread about attys -- lots!
http://www.e-cigarette-forum.com/fo...d-xl-18650-bottom-feeding-mod-vapage-com.html
You might want to search the thread for more info about the dripping atty's. They do feed -- but I don't know of anyone mostly using them.
Last edited:
Thanks tearose. I read through most of that thread but it has been a while so I will go back and search there.
I been using the 2 ohm BF atties that came with the Vmod and I picked up a couple of the 1.5 ohm BF atties from Vapage too. They work OK but after a couple days the draw started tightening up so I gave them a vodka soak. They were a slight bit better but not much. most of my juice is thin PG80/VG20.
I have a Cisco 1.8 ohm 306 I got from Avid that I have used but it actually runs a little hotter and the juice tastes slightly burnt. I think I am going to pick up a AERO 510 from Avid. I have wanted to try one since a couple people said they work good on the Vmod.
Thanks,
Please take care with the protected batteries on the VMOD.
A friend of mine had a problem last saturday, she used to put its battery with the + in the bottom of the VMOD XL (the battery is a AW IC P31) and she had a problem during the 3 first seconds. The Vmod went away in a big smog because the spring was stuck in the battery protection.
So take care.
A friend of mine had a problem last saturday, she used to put its battery with the + in the bottom of the VMOD XL (the battery is a AW IC P31) and she had a problem during the 3 first seconds. The Vmod went away in a big smog because the spring was stuck in the battery protection.
So take care.
here's my bottle mod. so no more tilting! I used a 16 gauge needle and a bottle nipple. just simply drop in the bottle and you're all set!
Last edited:
Nice Chad!
That's a good mod for those who are having trouble feeding, or just don't like squirshing.
That's a good mod for those who are having trouble feeding, or just don't like squirshing.
Nice Chad!
That's a good mod for those who are having trouble feeding, or just don't like squirshing.
I was just bored one day and started to picture this mod in my head. and this is the result. just simply drop the needle in bottle and you're all set.
Tonight on Click, Bang!
Russ will be giving away a Vmod!
Be sure to listen for your chance to win!
www.vapersplace.com
Russ will be giving away a Vmod!
Be sure to listen for your chance to win!
www.vapersplace.com
- Status
Similar threads
