Just picked up an aeolus and already drilled it out! What are your guys thoughts on it? Favorite builds for it?
RDA Thoughts on the Aeolus RDA?
- Thread starter Nuchuga
- Start date
- th_trl_thread_readers 0
- Status
got one a while ago when they first hit the market.
I like it other than the o-rings provided are way too loose for the top cap. The deck screws also dont capture anything above 24g very well, which frustrates me because I want to use it with nickel builds.
Mine also came with a 510 pin that is extremely long. I cant use it with many mods bc of how long it is.
Ive used dual 24g 7 wraps 3mm id and it was very good.
I like it other than the o-rings provided are way too loose for the top cap. The deck screws also dont capture anything above 24g very well, which frustrates me because I want to use it with nickel builds.
Mine also came with a 510 pin that is extremely long. I cant use it with many mods bc of how long it is.
Ive used dual 24g 7 wraps 3mm id and it was very good.
I just bought one of these, still waiting on it to arrive. This rda really had everything i wanted, especially the "leak proof" part, hopefully thats true or even half way true that would be nice.
How does it stack up in the flavor department? Ripp and Grimm just said that it was amazing -- does that mean better than the Magma/Plume/etc. amazing?
They sell a spare o-ring kit on their site with thicker ones to make the connections more secure. Its $1. The black o-ring in the spare parts bag is also thicker for the air flow ring. Replace the blue one with that for a more secure fit.
That was one of the first things i did with mine when it came in, i threw that black o ring on there. Works so much better. I think i will get that replacement kit cause this thing is ridiculously loose all over. No leaks so far though and ive been using it since Friday non stop. Definitely loving this rda.
The tank to the deck is really snug on mine. The top cap is a bit more loose, but its perfect for me to rejuice. The only piece that was too loose was the air flow ring, so the black o-ring fixed that. Maybe they've made improvements on them or I just got lucky.
I think you got lucky lol cause mine was exactly opposite of what yours was. The outer barrel is probably the most loose out of everything. If i could say 1 thing i dont like about this and there isnt much would be like stated above, that insanely long 510 pin that comes with the heat sink fin adapter. But i just dont use that, and if i did id probly just shave it down a bit. So its really not that bad, especially if thats all i have to really say thats bad about this.
yes it's a rebuildable atomizer but the original post was in the RBA section, and not in the RDA section within the RBA section... hope that made sense
With Ni200, fasten under the screw heads. This is what I do and it works great. It's not really recommended that you use post holes with this kind of wire anyway.
Sent from my HTC One M8 Harman/Kardon edition
Hi people,
just how long is the 510 on the heat sink adaptor? Is the 510 on the atty itself a resonable length??
Thanks!
just how long is the 510 on the heat sink adaptor? Is the 510 on the atty itself a resonable length??
Thanks!
The 510 on the heatsink part is ridiculously long in my opinion. But its perfect on the actual atty itself. I tend to not use the heat sink as much unless on a regulated mod, but thats just me.
To be honest im not sure the exact length. Im at work and its at home so i dont want to give you the wrong length. But its the longest ive ever seen and ive had a bunch of rda's, if your talking about the heatsink part that is and not the actual rda itself.
Ok! thanks again. If you remeber and can be bothered it would be good to know the length to see if it will fit any of the mods I have!
Cheers
steve
Cheers
steve
Yeah ill check for you when i get home after work. Unless someone else chimes in.
Its about 3-4mm i believe, if im reading it right. Sorry i suck at measurements lol sad i know. I would say closer to 3mm. Unless someone else has the exact length.
- Status
