UFS clear tank problem

[Moonwalker]

I made a stupid think - dismantled UFS all the way tolast piece just to see all the parts. Now there is no way that I can get the tank bank as it was, all the time I have 2-3mm space between tank and bout SS part's side. Any idea how to put it right? I already took off and on 5 times, changed sides and still the same result.

Stupid IGetcha rewiev.

 

[CaptSteve]

Here you go. Courtesy of brother Zoranth


UFS Assmbly (Atomizer Installation).pdf -- August 16, 2011 7:49 pm -- 159k

UFS Collection Tank Assembly.pdf -- August 16, 2011 7:49 pm -- 269k

UFS Connector Assembly (Exploded).pdf -- August 16, 2011 7:49 pm -- 233k

 

[Moonwalker]

Thank you very very much, I hope I'll get it back and start vaping

For these few tries, it can't go more than this:

 

[CaptSteve]

Have you put inside the steel parts of the tank o-rings stopping the clear tank to screw all the way in? If so take them out. The o-rings go around the clear tank although they are not required.

UFS Tank Assembly.pdf -- August 16, 2011 7:49 pm -- 319k

O-rings 4 & 5 go around the clear section next to the actual window

 

[Moonwalker]

So I should put o-rings? They were not originally on the window, but good that I bought spare pack. I'll will try that right away.

 

[CaptSteve]

No you don't need o-rings but your clear window should screw flush to the bottom and top cap

here is mine open

 

[CaptSteve]

and here it is all closed up

 

[CaptSteve]

Please make sure you haven't cross threaded the clear window which is easy to do in fact since it's got fine threads of plastic on steel

 

[Aron Gatt]

Thank you very very much, I hope I'll get it back and start vaping

For these few tries, it can't go more than this:

Could be the photo ...but It looks crossed threaded from the pic

 

[Moonwalker]

No vaping for me... I could now throw all that I bought through the window, that's how ...... I am.

I screwed it so hard that I couldn't get it unscrewed but needed to because it probably cross threads. And this is the result:

And now I go to ...... myself.

 

[Gabriel74]

That's why i took a ss window recently.
My clear is ok but i took it just in case...

 

[Moonwalker]

And now I can not buy new one. I don't know if this ever happened to anyone. Didn't even took one vape.

Sent from my LG-P700 using Tapatalk 2

 

[CaptSteve]

OK Moonwalker COV in the US has a steel replacement window in stock

GG Replacement Stainless Juice Window for UFS v1 or v2

I have a spare clear window which I can let you have on loan till you find a new one if you wish.

 

[Moonwalker]

Thank you for your offer, but I would probably do the same to yours. Just bad luck.

I must ask Vasiliss if maybe he has some leftovers. It will be about 15 days to arrive from the states + shipping fee, and I'm already drained.

At least it will be here in 5 days and cheaper shipping. I hate myself right now.

And I'm gonna try to vape it even like this, I want to try it even if it flods all over. But the problem is that I was screwing so hard, that now i can not detach part which screws to the tank from base for air regulation.

 

[CaptSteve]

When you screw in the clear window you do have to be careful not to cross thread because if you do you pretty much ruin the clear. I would suggest to call Vasilis he may be able to get another one from Imeo if he has some.
I'm sorry this happened to you, just bad luck if you need mine let me know and I'll send it to you.

 

[Moonwalker]

Thank's again, I'll keep that in mind as an end solution.

Now my biggest worry is how to detach parts from each other... it's so tight that even the ring for liquid flow control would not move. And if I took some pliers, I'm affraid that how lucky I am, I'll ruin my GGTS.

 

[CaptSteve]

No pliers Moonwalker. Put it in the freezer for 10min or so or try with rubber gloves on

 

[Moonwalker]

This is all awful, now I'm in paranoia that I totaly destroyed my GGTS.

Number 1 can not be unscrewed one from another.

Number 2 same thing, and number 3 could probably be separated only if I break plexiglass totaly.

This is a nightmare.

I am going to put it in a freezer for 10 mins, and hope that that will do the trick.

 

[CaptSteve]

If you still can't unscrew #1 and #2 then put them in warm water for a few minutes and then try unscrewing them with rubber gloves on.

 

[Aron Gatt]

Oh ..I feel so sry mate ...damn