unsure of issue.

[mavieboy]

Finally came in today 4hrs trying to set it up but still cant i dun understand where is d negative and positive point and also how to wrap in in the centre besides d mesh.. 3attempts all fail it read as atomizer short on my evic..

take ur time bro, watch some reviews on aga-t, you don't anything abang here can help u =)

 

[sgvap22]

Finally came in today 4hrs trying to set it up but still cant i dun understand where is d negative and positive point and also how to wrap in in the centre besides d mesh.. 3attempts all fail it read as atomizer short on my evic..

Dude, try this video: AGA-T2 from safercigs.co.uk - YouTube

The tall center post is Positive, the screw next to it is Negative.

If it shorts, either your mesh not oxidized properly, or you neg or pos wire touching somewhere.

 

[Aizerson]

alright thanks will try again this evening at home.. neg or pos touching somewhere like..? isnt it suppose to be under the screw and the one on the positive post in the middle of the 2 round thing.. nvm i'll keep trying yest try until very sleepy already..

 

[Aizerson]

normally you guys cut ur mesh how big to before rolling it.. if i do 35mm x 20mm is that ok..?

 

[Ravi1234]

Do a dry burn... It is magical.

 

[madhero]

normally you guys cut ur mesh how big to before rolling it.. if i do 35mm x 20mm is that ok..?

Mesh size largely depends on wick hole size.

 

[eyespan]

normally you guys cut ur mesh how big to before rolling it.. if i do 35mm x 20mm is that ok..?

A little small for T2 lah. I cut 5 X 5.

 

[eyespan]

That's Centimeters.

 

[Aizerson]

oh alright will try again tonite.. goin to buy a drill bit and try the drill bit method..

 

[invisibl3]

oh alright will try again tonite.. goin to buy a drill bit and try the drill bit method..

bro meet me up tonite i show u how to do up the mesh.. bring some of your nice ejuices for me to try if you are available

 

[Aizerson]

bro meet me up tonite i show u how to do up the mesh.. bring some of your nice ejuices for me to try if you are available

alright boss.. i will give you a call later..

 

[Aizerson]

i've set up my coil at 2.5ohm.. flavour can taste a bit already.. but problem is the vapor is not as expected.. does enlarging the airhole on the top cap help in achieving more vapor..?

 

[madhero]

i've set up my coil at 2.5ohm.. flavour can taste a bit already.. but problem is the vapor is not as expected.. does enlarging the airhole on the top cap help in achieving more vapor..?

If its a Genny, try going lower. Flavor is better "down" there. If you're able, try lower then 1.5. My usual is 0.8-1.0
And yes, enlarging the air hole does increase vapor production, just make sure not to make it too big, or u may get a really lose draw.

 

[muteego]

What's your voltage setting at?

 

[mavieboy]

If its a Genny, try going lower. Flavor is better "down" there. If you're able, try lower then 1.5. My usual is 0.8-1.0
And yes, enlarging the air hole does increase vapor production, just make sure not to make it too big, or u may get a really lose draw.

that's really low. too bad my zmax v2 cant handle resistance lower than 1.5ohms

 

[Aizerson]

What's your voltage setting at?

mine is set at 3.9 volt anything over that i can taste burn taste..

 

[madhero]

that's really low. too bad my zmax v2 cant handle resistance lower than 1.5ohms

Well, that's when mech mods come into play.

 

[invisibl3]

time to invest in a mech mod genny style attys