VIDEO: GotVapes Sapphire complete tear-down/dis-assembly

[msimindlessmsi]

Completely took apart a GotVapes Sapphire. After prob 20+ fills the draw was getting a bit tight so I decided to take it apart. Working great yet again!

Audio skips a little bit from time to time in the video so I might sound like an alien for a second.

Check it!

 

[VapingMattCA]

Great video! I fixed one of my Saphires that was leaking. The rubber o-ring that is about the blue stuff wasn't seated properly.

 

[msimindlessmsi]

Sweet! Glad I could help somebody out with this video. I am always tinkering with my e-cig stuff

 

[mwa102464]

Forget that CE2 Wick, put a piece of SS 400 MESH on that beast and you will have the best wick of them all, there are some things you need to know though before you just use this Mesh, but it is the ultimate wick for this.

 

[msimindlessmsi]

Forget that CE2 Wick, put a piece of SS 400 MESH on that beast and you will have the best wick of them all, there are some things you need to know though before you just use this Mesh, but it is the ultimate wick for this.

Is that what they wrap the atomizers in? The metal mesh?

 

[SynJyn Smyth]

How many seconds do you dry burn for?

 

[msimindlessmsi]

How many seconds do you dry burn for?

Not really a set a mount of time. I burn for a few seconds then blow on it to cool it off. Keep doing that until there is no more smoke and the coil glows a bright orange.

 

[SynJyn Smyth]

Not really a set a mount of time. I burn for a few seconds then blow on it to cool it off. Keep doing that until there is no more smoke and the coil glows a bright orange.

Thank you, this will help out alot.

 

[mwa102464]

Is that what they wrap the atomizers in? The metal mesh?

Yes,,,I believe it is Nichrome Wire they use for Attys some manufacturers may use different types, but if you use ss 400 mesh the flavor you get will be even better in the Sapphires, there are also other types of Wicking material that are much better as well this =http://www.omega.com/ppt/pptsc.asp?ref=XC_XC4_SLEEVING XC4-116 being just some super stuff ! it does not burn at the temp we operate with, I've been using both together on some things I'm projecting on and the flavor is like nothing I've ever had before with my juice, and just plain ss 400 Mesh as the wick in those Sapphires is super, you need to roll a real tiny thin piece of it and slide it in where the wick goes in place of what your using. You can buy the stuff at the mesh factory or McmaterCarr dot com.

 

[harmonic]

MSI - its not the metal stuff the atty is wrapped in when you take it apart. but do get some to try like he said lol
MWA - i think he ment the silver metal stuffed packed around the ceramic shell in the atty when you take it apart.

 

[msimindlessmsi]

MSI - its not the metal stuff the atty is wrapped in when you take it apart. but do get some to try like he said lol
MWA - i think he ment the silver metal stuffed packed around the ceramic shell in the atty when you take it apart.

Yes that is what I was talking about. Might be worth checking out. After so many dry burns the wick inside the coil was GONE! Guess it does burn eventually.

 

[SmokingRT]

Well I have been inspired by you vid MSI. As you all know I always say I am not a modder (I am certain most of you are tired of hearing it). My sapphires have worked flawlessly. That however is the reason I am going to take one apart tomorrow when I am off work. Just in case I have one at some point that I need to look at.

 

[harmonic]

good luck sir. you can do it!

 

[msimindlessmsi]

Well I have been inspired by you vid MSI. As you all know I always say I am not a modder (I am certain most of you are tired of hearing it). My sapphires have worked flawlessly. That however is the reason I am going to take one apart tomorrow when I am off work. Just in case I have one at some point that I need to look at.

You could always wait till one gets to the point where you find it unusable, then take it apart and you could possibly bring ti back to life.