What Builds to use on our ProVari,s

[TFL!]

With the Voltage, wattage and amp limits we have what do you use on:
Kanger Pro tanks?
Kayfuns?
On Pro tanks I use
32 gage kanthal wrapped on a 2mm screw in the threads spaced coil
7/6 wraps. for 2.2 Ω
3.6 to 4 Volts
about 5.5 to 7 watts
Wicked with 2mm silica
.
Hope to get list of builds to help new and old users of these toppers and ProVari.

 

[BadTrainDriver]

28 gauge, 1.5ohm single micro coil wicked with KGD cotton, 3.6 to 4.2 volts, KFL+.

That's my go to setup almost every day.

 

[Baditude]

I use the same build and voltage ranges as Bad Train Driver for my KFL+.

 

[BadTrainDriver]

I use the same build and voltage ranges as Bad Train Driver for my KFL+.

No. I use the same as you.

 

[MonsterKenny]

Agreed.. Perfect build for the provari.

 

[ENAUD]

With the Voltage, wattage and amp limits we have what do you use on:
Kanger Pro tanks?
On the Protank 2's I add an aerobase, and use the stock 1.8Ω coils (these almost always measure around 2.2Ω), out of the box I pull the silica out and re-wick with Peaches & Cream cotton yarn. When those coils are shot, I re-coil with 2.2Ω no res-resistanse-no res wire, wrapped on a 1/16" drill, spaced coil. I typically drive them at 3.6V-3.8V to taste.
Drippers?
I run Igo-L, Igo-W, Magma, and Enigma, single coil, 30 Guage kanthal wrapped on a 1/8" or 5/32" drill bit, 1.4Ω-1.6Ω, compressed coil, wicked with cotton, air holes drilled to 1/8" or so. I drive these at 3.6V-3.8V.
Kayfuns? 30guage kanthal, same build as my drippers, 3.6V-3.8V.

 

[TFL!]

I want to thank those that replied with their builds. Hope more post.

 

[Deryan3]

28 gauge, 1.5ohm single micro coil wicked with KGD cotton, 3.6 to 4.2 volts, KFL+.

That's my go to setup almost every day.

I agree, love this set up

 

[HippyBKC]

I build 28 gauge macro coil (2.4) on my russian, 1.3 ohm, wicked with rayon. It's perfect.

 

[Lurch]

Man, I run my volts a lot lower then most.... I using 1.4 Ohm on my Russians at 3 - 3.2 volts. I like a cool vape!

 

[HippyBKC]

I run mine bewteen 3.2-3.4. Also enjoy a cooler vape.

 

[supersport13]

I use the same build and voltage ranges as Bad Train Driver for my KFL+.

What size rod do you use to wrap and how many wraps? Also, what do you use for wick? Thanks Baditude!

 

[witch1]

I coil my Zen Atty Pro at 1.5 and set my volts at 4.3-4.5-depending on juice.

 

[woodardjd]

28AWG A1, 9 wraps around a 2mm bit. 1.5 ohms. Wicked with ShiSeido cotton(easier to get here than KGD).
I tend to fire it at 4.0 volts unless the pressure's on. Then I'm around 4.5.
Same build on the Russians and the Taifuns.
I don't use ProTanks so I'll be no help there.