what volt,what ohms,what watts you prefer?

[arar1971]

hi
i am planning to order provari or lavatube and i wanna know with what volt,what ohms you like or what watts you usually prefer? low volts high ohms or high volt low ohms taste better? what watt range gives good taste?

 

[Off Topic]

I use these on my provari:

Crystal Clear Vaping

I run around 4 volts.

You can run dual coil heads up to about 2.5 ohms on a provari. I don't know what the limit is on single coil. Much over 4 would probably give you a meh vape.

If you have the $$ for the provari, get it. It's much more solidly built. It's worth every penny.

 

[AttyPops]

Single coil 2.8 - 3.1 ohms on vv mods. Around 4.8 - 5.0 volts. On the Vivi Nova...I'm lower ohms/volts due to wanting different gauge wire.

Watts vary a bit depending on the head/atty. Around 7-8 watts. Some juice cooler particularly fruit flavors since they burn easily.

 

[Daniel13]

i'm the strange one, 4 volts on a boge LR is great for me, vivi novas i prefer turned down a bit, 3.8v on 1.8ohm, 4v on 2.4ohm, and 4.2v on 2.8ohm.
there are times when i push my boges at 4.8v on my twists and i know it cuts it off at a safe point.

 

[mooreted]

4.8v on my Stardust, 4.0v on my Phoenix bottom coil, 3.7v with blueberry cream because it seems to taste burnt at higher voltage.

 

[Gamekeeper]

I am using a lavatube and Smok Mega XXXL DC Carto. 4v is my minimum, 5v -5.5v most of the time. I really cannot complain about the vapour released or the power. I use 2000mah high drain batteries, and even though one would last 24hrs, I change them at 12hrs for max power.

 

[Thrasher]

Volts, ohms and watts oh my!

2.2 ohm heads on my t2 about 3.8 ishV
1.8 ohms on my RBA about 3.4-3.6V
2.0 on my nova. about 3.5 - 3.8 ish

the idea behind the VV is you get to find the sweet spot for you and always finding the exact ohms when you replace something that worked good is less importaint now.

 

[Black Strat]

For me about 3.4-3.8 volts on 1.8 ohm atties, 3.4-3.6volts for 1.5 ohm DCT cartos, and 3.6 -4.2 volts for 2.4 ohm atties.

 

[gardnerd4me]

I mix 'em up a bit, guess it's considered low, but it works for me on my Provari.

V3 stardust @ 2.4Ω = 3.5V
Vivi Nova tank @2.8-3Ω = 4.2-4.5V
dud @ 1.8Ω 3.5V

Some juices need less heat, some need more. Love being able to change volts to find where the juice needs it.

 

[arar1971]

i am new but i learnt a lot from here.

Volts, ohms and watts oh my!

2.2 ohm heads on my t2 about 3.8 ishV
1.8 ohms on my RBA about 3.4-3.6V
2.0 on my nova. about 3.5 - 3.8 ish

the idea behind the VV is you get to find the sweet spot for you and always finding the exact ohms when you replace something that worked good is less importaint now.

 

[Fishtec]

4.6/4.8 on my 2.8 nova 3.6/3.7 or so on my genesis

 

[Syn007]

You have to factor in the brand/type of juice really. The flavors will react differently at various heat and whether they taste "good" is very subjective.

 

[Gatillero1980]

AC9 Genesis atty 1.5 ohm coil @ 4.7V soooo around 14W+

 

[tj99959]

So many things will cause you to want a different power setting. Even the time of day can make a difference.

Right now my Provari has a 2ohm dripping atty on it and is set at 4v, that's 8 watts.
My LT has a different kind of dripping atty that is 1.7ohm on it and is set at 3.3v, that's only 6.5 watts to produce the same TH & flavor.
My old 3.7v Silver Bullet has a 1.3ohm dripping atty on it, and at 10.5 watts knocks the socks off both the Provari and the LT.