What wattage for your kayfun?

[chiliphil1]

Hey everyone, I just got myself an istick 30w the other day and tossed my KFL on there and after a few very unsuccessful attempts I finally found my sweet spot, 16.5 watts. I am running a parallel coil made from 2 strands of 30g, side by side not twisted. This coil comes out to 1.5 ohm according to the istick. I was wondering what all of you other kayfun users are running wattage and coil wise. I fired it at 30w one time to see what happened and that was like using my dripper with no juice in it! I like it where it's at though, big improvement over my mvp that I switched from.

 

[Garemlin]

I typically run a 1.3Ω - 1.6Ω single micro coil. My wattage is usually between 11w - 14w. Any higher and it tastes off. Of course I run 50/50 and 60PG/40VG juice. I have seen people go as low as 6w and as high as 20w on a similar build. All depends on the user I guess.

 

[HDMontana]

I'm using 1.2 - 1.3 ohm coils. 10 wraps of 26 gauge kanthal at about 2.7 mm. Run it art 18 watts in my Kayfun V4's.

HD

 

[Sirfuji]

28 gauge 2.5mm for around 1.4~1.6 ohm. I usually go with between 10 and 11.5 watts.

 

[nasca]

1.1 ohm on a mech mod, so about 16 watts.

 

[Monotremata]

I typically run a 1.3Ω - 1.6Ω single micro coil. My wattage is usually between 11w - 14w. Any higher and it tastes off. Of course I run 50/50 and 60PG/40VG juice. I have seen people go as low as 6w and as high as 20w on a similar build. All depends on the user I guess.

That's my setup pretty much on both the KFL+ and KF4..

 

[chiliphil1]

I found yet another way that I like this set up. I made a new coil with 28g that came out to .7 then I put in zombie blood juice, as far as my knowledge this is a 100%vg juice, cranked the istick to 18.5 and have found the best flavor imaginable in my kayfun, it has never been this good, ever.

 

[93gc40]

I do single 1.8-2.1ohm coils with 30awg at 7-9 watts, on a kicked mod, using NET juices @70%PG and 12nic, changing the cotton every 2 days. Contemplating getting some 28 next time I buy wire, but I might buy thinner and twist it instead.

 

[yellowrider]

10 wraps of 28awg puts me around 1.5-1.6ohms and 3.4v or 7.1 watts for me.. It blows satisfying clouds with favor.
But regardless of ohms or watts, if it is not set up properly its not going to perform.
These attys perform best in lower power settings with correct build.

 

[TrollDragon]

28 gauge 2.5mm for around 1.4~1.6 ohm. I usually go with between 10 and 11.5 watts.

Same here at 12.5W

 

[dhood]

I have two Kayfun Lite V2s and a Kayfun nano, I usually shoot for 1.2 to 1.3 on a 28 gauge Kanthal single microcoil. I generally run mine around 13-14 watts.

 

[orion7319]

I typically run a 1.3Ω - 1.6Ω single micro coil. My wattage is usually between 11w - 14w. Any higher and it tastes off. Of course I run 50/50 and 60PG/40VG juice. I have seen people go as low as 6w and as high as 20w on a similar build. All depends on the user I guess.

Sounds about right. The gauge of wire your using will influence how much wattage your going to want to use.

 

[chiliphil1]

I found yet another way that I like this set up. I made a new coil with 28g that came out to .7 then I put in zombie blood juice, as far as my knowledge this is a 100%vg juice, cranked the istick to 18.5 and have found the best flavor imaginable in my kayfun, it has never been this good, ever.

Correction to this, I am using 26g 8 wraps making .7