What's your favorite RBA (rta or RDA)?

[stanthemanchan]

My Aqua leaks from the air-hole, the juice feed control seems to do nothing and I haven't filled it yet without getting liquid all over me. It is a clone though, so maybe that explains it.

Are you using the bottom fill method on your Aqua? https://www.youtube.com/watch?v=UiR-tckIXvM

Using this method, I can fill the tank up to its maximum capacity of 3.0 ml and there is zero leaking or flooding of the air chamber. I also ordered the replacement PMMA tank from fasttech and it has helped a LOT.

$1.72 Replacement PMMA Tank for Aqua RBA Atomizer at FastTech - Worldwide Free Shipping

 

[Rule62]

Man, if the Odin had post holes and a t-post positive it would be perfect. I just can seem to go back to screw-down wire connections. Esp with dual coils.

I agree. If the Odin had a T positive post, it would be just about perfect. The T positive post is one of the reasons I always list the Brass Monkey among my favorite RDAs. Hmmm...I wonder if I could convert one to bottom feed for the Reo.

 

[super_X_drifter]

Super x, I totally agree, I don't have one. But if I made an atty that's pretty much exactly how it would look like. How reduced is the chamber on that bad boy?

The actual inside top portion of the chamber (from the air slots up) is about 18mm wide x 5mm tall. From the air slots down is mostly consumed by the base (the juice wells are milled down into the base), the center posts and the screw heads.

I'd say it's pretty small. And robust. The outside top of the cap is about 10 above the air slots and inside about 5mm is used up for drip tip mount. The inside is also reduced down to 18mm.

 

[Tbev]

Thanks bro that sounds great, and it's just super clean too. That pdib with odin on top I wound venture to say is the be

st vaping device available that money can buy. I love it, honestly I don't do wood, wooden anything just doesn't do anything for me but that is the Baddest feeder available.
That is, as you know, due to the fact that the true unicorn, that only I possess, is currently the only one I've made...

 

[super_X_drifter]

Thanks bro that sounds great, and it's just super clean too. That pdib with odin on top I wound venture to say is the be

st vaping device available that money can buy. I love it, honestly I don't do wood, wooden anything just doesn't do anything for me but that is the Baddest feeder available.
That is, as you know, due to the fact that the true unicorn, that only I possess, is currently the only one I've made...

Bro, you just might have to make one more?
I got a chalice and cyclone with the name Tbev on them

 

[Tbev]

I'm not allowed to answer that bc I'm not a registered ecf vendor, they banned me for talking about making more..
Thanks tho bud!

I am liking this magma I just got, I think 22ga. Is just a bit too hot...

 

[sKo713]

Krakens (stainless, builds drill out the air holes, low sub ohm, no fuss no need to drip) , Tobh and IGO-M (I just hate drippin' those drops), Fogger 4.1 (just hits hands down better than Kayfuns and Russians). Still waiting to try all these on a 100 watt box if they will ever ship.

 

[lasttango]

If my Atomics didn't leak on me when I vape in bed ;-) I'd say they were my favs... my crown, cyclone and plume veil are nice...

really want a magma!

 

[stanthemanchan]

If my Atomics didn't leak on me when I vape in bed ;-) I'd say they were my favs... my crown, cyclone and plume veil are nice...

really want a magma!

If you're worried about a leaking atty while vaping in bed, then you may want to reconsider the Magma. It is a very good atty, but it can be leaky, especially if you're not careful while filling it. Maybe take a look at the CATs RDA.

 

[Tbev]

Just got another quasar and a magma today, I didn't think this was gonna be the case but i think the magma had a slight edge over my previous favorite atty the quasar....
It's not the best looking atty, the quasar definitely has the upper hand in that department.

 

[jaxgator]

Just got another quasar and a magma today, I didn't think this was gonna be the case but i think the magma had a slight edge over my previous favorite atty the quasar....
It's not the best looking atty, the quasar definitely has the upper hand in that department.

Nice!

Function over form for me, everytime. Heck, I own a SQr and love it so that should tell you something.

 

[regal55]

The brass monkey, can be totally rebuilt in less than 5 minutes with premade coils. The 4 posts with set screws is a delight and it hit great. I don't think there is a better RDA.

 

[entropy100]

the cats rda by rjmod its pretty sick. quad posts . i am currently running triple twisted 28 gauge 5 wrap quad coils and it hits like a beast.

it is really good against leaks since it has an outer shell over an inner shell. and its hits like a champ with great flavbor

 

[The Ocelot]

Rüzgar

10 char

 

[Wow1420]

I'm kinda torn between the Magma and the Origen. The Magma is easier to build, otherwise I find them similar in performance. The Veritas is the only other modern design I've tried and it didn't match up to the other two. But this could be the fault of the particular clone design I have.

The KF is the only RT I've tried, very happy with it.