Working mans belt pouch for the mini.?

[rebar]

Im looking for a sturdy belt pouch for my mini. I get into some nasty stuff at work and need it protected yet accessible. I leather belt pouch with snap top would be great. Anyone?

 

[Mvgratz]

Im looking for a sturdy belt pouch for my mini. I get into some nasty stuff at work and need it protected yet accessible. I leather belt pouch with snap top would be great. Anyone?

Only if either A) you turn the firing switch to the "OFF" position, or B) it doesn't cover the firing button... When my mini gets here in the next day or two I plan on a trip to wally worlds cell phone holster/pouch department to find one to fit mine. I have cell phone holders that fit my grand and woodvil perfecty...

 

[mwa102464]

There is a guy here on the ECF making belt holders for mods, if either of you haven't seen him or his post PM me and I will PM you back his info, they look quite nice and have either a loop for the belt or a clip for the belt. $25 is the cost I believe, they are top notch leather and very well crafted, built to fit any mod.

 

[rebar]

Only if either A) you turn the firing switch to the "OFF" position, or B) it doesn't cover the firing button...

Thanks. I would need it deep enough to cover the drip-tip so the button wouldn't be near the top. That would require me to pull it out by the drip-tip though.

I would think a vendor would have offered something like this by now.

 

[Mvgratz]

This is the vendor MWA was talking about. He can make just about anything you could want...
http://www.e-cigarette-forum.com/fo...forum/177608-griffs-leather-mod-holsters.html

 

[rebar]

Perfect! Thanks

 

[Sterno]

ya i got my mini and grand leather holders from wal mart and made alterations where needed

 

[Sterno]

forgot to mention that my woodvils fit in the grand pouch also

 

[mlinky]

rebar, since you will be on-site with a Mini, you might want to make one of these nifty button covers that dogzlife came up with http://www.e-cigarette-forum.com/fo...uick-thoughts-my-first-reo-2.html#post3089236

This mod would make it much easier to fire your Mini if you wear work gloves.

 

[rebar]

Thanks. I really need griffin to build me a custom holster for work. I'm upside down sometimes.. I never know.. crawling through steam tunnels etc.

Iv got 1 1/2" wide X 3/4" deep X 3 1/8 tall without a cannon drip tip and LR306. Can anyone give me a total height with the cannon drip tip and LR306?
Cannon | Drip Tips | Cisco 306 | LR | Atomizers | Cherry Vape

 

[worknomore]

Thanks. I really need griffin to build me a custom holster for work. I'm upside down sometimes.. I never know.. crawling through steam tunnels etc.

Iv got 1 1/2" wide X 3/4" deep X 3 1/8 tall without a cannon drip tip and LR306. Can anyone give me a total height with the cannon drip tip and LR306?
Cannon | Drip Tips | Cisco 306 | LR | Atomizers | Cherry Vape

On my Grand the Cisco 306 and Connon Black Drip tip sits 1 and 9/16th of an inch above the highest point of the grand.

 

[rebar]

On my Grand the Cisco 306 and Connon Black Drip tip sits 1 and 9/16th of an inch above the highest point of the grand.

Thanks. The grand unit must be different form the mini. Here's what I was told about the mini.

The CherryVape Cannon Drip Tips are 1.5 inches long per the manufacturers web site...
Cannon | Drip Tips | E- | Cigs | Cigarettes | Cisco 306 | Cherry Vape
The juice well on the reo mini is 1/4" deep, so I would venture the guess that the cannon drip-tip will stick up 1 1/4" inches above the mini's height.

 

[Big Hitter]

The mini well is not 1/4 inch deep. It may be 1/4 inch tall on the outside but its only about 1/8 inch deep.

 

[rebar]

Thanks.

Sounds like a few people don't know how to read a tape measure. Iv been told the mini was 3/4" deep and then its 5/8"

So right now I hope I have the most important dimensions..

1 1/2" wide X 5/8" deep. Depending on the drip tip, give or take .. 4 1/2 tall.

Wow..

 

[Rhapsodies Fire]

Thanks.

Sounds like a few people don't know how to read a tape measure. Iv been told the mini was 3/4" deep and then its 5/8"

So right now I hope I have the most important dimensions..

1 1/2" wide X 5/8" deep. Depending on the drip tip, give or take .. 4 1/2 tall.

Wow..

Nice catch...its 3/4" deep. I promise...I can read a tape. And I fixed that post.

 

[Mvgratz]

On my Grand the Cisco 306 and Connon Black Drip tip sits 1 and 9/16th of an inch above the highest point of the grand.

Well, OP since this post conflicts with what the manufactor's web site says the length of the cannon drip tips are (suppose to be 1 1/2" long)...I would sugguest waiting till you have all the items your going to use in hand and doing your own measurments if it needs to be that precise.

BTW, I assumed that the drip wells were the same depth that they are tall, but now that I have both in front of me that is NOT the case. The mini's juice well depth looks to be 1/8", and the grands drip well about 5/32nds"...

 

[rebar]

Nice catch...its 3/4" deep. I promise...I can read a tape. And I fixed that post.

Christ.. I already ordered the holster
.

 

[Mvgratz]

Christ.. I already ordered the holster
.

I appologize for copying and pasting what I thought to be "confirmed" measurements.
Maybe you can catch Griff in time to make the adjustment...

 

[rebar]

Reminds of when I asked for a measurement on the phone. The kid at wall mart said it was the little mark after 1/2"

Now is that 9/16 or 33/32?

Griffin is going to be .......

 

[Big Hitter]

The mini's juice well depth looks to be 1/8", and the grands drip well about 5/32nds"...

Exactly correct.