Authentic Rincoe Jellybox SE Kit is an ultra-small but powerful vape pod system, also a continuation of the Jellybox series. constructed with a zinc alloy body and satin material finish and a PEPG tank section for durable construction. It has a range of coil options between 0.3ohm and 3ohm, and has two types of coils to choose from: Mesh 1.0ohm Coil and Mesh 0.5 Ohm Coil.

Rincoe Jellybox SE Vape Kit near me SPECIFICATION

Material: Zinc alloy+PCTG+PC
Battery:500mAh Built-in
Pod capacity: 2.8ml
Power: 10-13W
Input: 3.2-4.2V
Coil resistance: 0.3-3ohm
Charging specification: 5V/1A
Efficient: 95%

Powered by 500mAh Built-in Battery, and you can expect a full day of vaping pleasure when using a Type-C USB port, which allows a 5V/1A charging specification. Rincoe Jellybox Nano Pod can hold up to 2.8ml of E-liquid, you can refill all sorts of different juices you want, satisfying both nic-salt e-liquid and freebase e-liquid.

You could go to vape shop online to learn more details.

Quick Link:Rincoe Jellybox SE Pod System Kit 500mAh 13W

You may also like:Vaporesso XROS Nano Pod System Kit 1000mAh

VOOPOO VINCI Q Pod Kit

VINCI Q Pod Kit inherited VOOPOO's unique ITO atomization tech to bring the purest flavor. It is casted by the two-tone textured injection mold and has 6 macaroon colors. Made of lightweight PC & ABS materials, it is durable in use and fashionable in appearance. VINCI Q Pod Kit is powered by a built-in 900mAh battery with Type-C charging. It comes with 11-15W adaptive power, which can intelligently match the best power to 0.8ohm or 1.2ohm cartridge. Benefit from the GENE chip and smooth airway, it has button/auto dual vaping modes and faster ignition to bring you better vaping experience. It also has 2ml e-juice capacity and easy top filling system. In addition, VINCI Q Pod Kit is compatible with VOOPOO VINCI Pod Cartridge, VINCI Pod Cartridge Royal Edition and Drag Nano 2 Pod Cartridge.

Details:
1. Inherited VOOPOO's unique ITO atomization tech
2. Two-tone textured injection mold, 6 macaroon colors
3. Lightweight ABS and PC material, durable and fashionable
4. Adopts the latest mesh tech to bring wonderful taste
5. Button/auto dual vaping modes to satisfy your preference
6. Strong GENE chip and smooth airway, faster and more sensitive
7. Lights on and off along with each puff
8. Built-in 900mAh battery, Type-C charging port
9. 11-15W of adaptive power to match the best power to 1.2/0.8Ω cartridge
10. 2ml full-view cartridge, easy and leakproof top filling system
11. Fit for VOOPOO VINCI Pod Cartridge, VINCI Pod Cartridge Royal Edition and Drag Nano 2 Pod Cartridge
12. Overtime/overcharge/over discharge/over temperature/short-circuit/output over-current protection





VINCI Pod Kit Royal Edition

VINCI Pod Kit Royal Edition not only inherits the portable appearance of VINCI Pod, but also utilizes classical relief sculpture technology accompanied by aeronautical material of 6061 aluminium alloy. VINCI Pod Kit Royal Edition has 800mAh built-in battery with 11-15W power range. Equipped with a top-fill visible cartridge of 2ml capacity, it is convenient for you to refill it. Upgraded leak-resistant function is applied to VINCI Pod Kit Royal Edition. There are two pods in the package: mesh 0.8ohm pod and mesh 1.2ohm pod. In addition, VINCI Pod Kit Royal Edition is compatible with the cartridge of Vinci Q, Drag Nano 2 and Vinci Pod.

Details:
1. Compatible with the cartridge of Vinci Q, Drag Nano 2 and Vinci Pod
2. Relief sculpture masterpiece
3. Classical and modern pattern
4. 2ml visible cartridge, top filling
5. Auto-draw mode, 3-color smart LED light
6. 6061 aluminium alloy for more advanced experience
7. Comfortable and unique grip feeling
8. Upgraded leak-resistant
9. Equipped with two pods of mesh 0.8ohm and mesh 1.2ohm
10. Adjust airflow with button on the side of the device
11. Type-C fast charging
11. 800mAh built-in battery
11. Multiple protection: Overtime/Short-circuit/Overcharge/Output Over-current/Over Discharge/Over-temperature Protection

Hi there, I'm an a new member here.
Want to make friend with you, fond of the e-cig!

Here comes a new disposable vape from Vbar - Ace Lite, which comes with a completely different outline design from Cubo Series, bringing a brand new look to you.



Main Features:
1. High-end & elegant outline design, exquisite& soft hand feeling
2. Real fresh flavor with upgraded atomization technology
3. 2ml prefilled e-juice with 2% nicotine strength
4. Large 500mAh built-in battery for 600 puffs' vaping
5. Rich 15 flavors to meet your different flavor needs

You can enjoy some new flavors that you couldn’t find from Cubo Series, such as M·A·P(Mango Apple Pear), Menthol Breeze, Pineapple Orange, etc.

Learn More:
Vbar Ace Lite

ElegoMall provides worldwide shipping and competitive price for all the customers, register on ElegoMall Now to get your new user coupon that is worth $1,000 (wholesale only) and 20% OFF coupon for retail and then enjoy better price of Vbar Ace Lite the best disposable vapes.

And for any inquires of disposable vape wholesale in China, feel free to contact ElegoMall.

Hello again. I’m back with another review for Freemax. This time I’ll be looking at the Marvos RTA Pod. This pod is compatible with all of the Marvos series of pod mods and can work with the Marvos S with the pod tank base. The pod has two sided airflow control and the control does have a positive stop. The pod uses an 801 drip tip that has a V shaped groove at the edge to help it be more spit back resistant. The pod has a 3.5ml capacity which isn’t bad but nothing to brag about. Before I go into too much detail, let’s take a look at what’s included and some features then I’ll talk about my experience with it.




WHAT’S IN THE BOX?

1* Marvos RTA Pod 3.5ml
1* Cotton
1* 0.15ohm Mesh Coil (60W max)
1* 0.25ohm Mesh Coil (40W max)
2* Sealing Ring
1* Bending Tool
1* Screwdriver
2* Phillips Head Screw
1* User Manual
1* Desiccant




SPECIFICATIONS:

Size: Φ27.0*42.5mm

Pod Capacity: 3.5ml (standard version)

Drip Tip: Replaceable 810 drip tip

Filling Type: Bottom filling

Compatibility: Compatible with all Marvos products




FEATURES:

1. First rebuildable pod of Freemax for Marvos series products

2. two-side & top airflow control

3. Replaceable 810 drip tip for DTL vaping needs

4. V-shaped groove design at the edge of the 810 drip tip

5. Compatible with both replaceable mesh coil and DIY wires

6. A spring-loaded ceramic block to support the cotton

7. Twist-lock design for building easily

8. 3.5ml e-liquid capacity, bottom refill system

9. Strong magnets guarantee quick and perfect match with the mod














INITIAL THOUGHTS:

The packaging for the Marvos RTA Pod is the usual blue, white, and black colors with a picture of the pod on the front of the box. Rather than put the contents on the back, they chose to put the contents list on the side of the box. The box opens from either end and the pod is held in a plastic tray with the accessory items tucked underneath the tray.





I have to be honest. I was a little disappointed by two things that I noticed upon opening the box and taking it apart and inspecting the contents. The first thing I noticed was that the tank section of the pod was not glass. It’s PCTG or something and is frosted a little which makes it slightly difficult to see the liquid level if using a clear liquid but not too bad. All of the pictures on the website show a clear tank section making one think that it is clear glass. The sample I received is not clear like the pictures. The second thing I noticed is that there were only two mesh strips included. I feel like more mesh strips could have been included without affecting the price too much.

On a positive note, the tank is very easy to disassemble and clean. To remove the base it is just a quarter turn to loosen and remove. I really like that. Just like the other Marvos pods, the fill port is found on the bottom of the pod and has what feels like a good quality silicon plug. The opening was large enough to use the 10 and 50ml bottles that I normally use. A glass dropper might get a little messy but most plastic bottles should work fine. There are four magnets on the bottom of the pod and I thought that would be plenty to hold it firmly in place on the Marvos 60w that I used for testing but found that if I place a finger on the pod while firing that I can tip the pod.

The drip tip used on the pod is an 810 drip tip. It has a V shape that helps to prevent spit back but it is replaceable if you would like to use your own tip which I did.





I was very surprised by the amount of airflow that the pod offers. I ended up running the airflow less than half open the entire time I used it. It really offers a lot of airflow for a small tank. There are two narrow but long airflow slots. The airflow adjustment on my sample was very loose to turn but did have a stop. It was loose enough that I found that I frequently accidentally moved the airflow adjustment when taking it in and out of a pocket.

It’s hard to see in the picture below but it does have the Marvos name and RTA Pod etched in the bottom of the pod.



The build deck has a single Philips head screw on each side that must be loosened to insert the mesh coil. The literature says you can use standard wire coils also but I did not try one since I felt it necessary to test the pod with the included mesh strip coils. Included in the package is a hollow metal tube that is used for shaping the mesh before inserting it. Simply hold the mesh strip and bend it tightly around the tube.

I experienced some trouble with my first attempt at building the deck. When you loosen the deck screws, the clamps are not spring loaded which made it hard for me to insert the coil without getting it out of shape. The clamps kept sliding closed while I was trying to insert the mesh. In the center of the deck is a ceramic plate that does have a spring under it to push the wick up against the mesh coil. I thought I had enough cotton in the deck and trimmed and thinned the tails out quite a bit but was getting intermittent atomizer short messages and somewhat dry hits. I ended up tossing the first coil which was the .15 mesh coil along with the wick. On the second build I installed the .25 ohm mesh coil and stuffed the wick under the coil as tight as I could get it. Once again I trimmed and thinned the tails. This time I had success. I immediately could tell the cotton was more saturated but it did take a little while to break in the new coil and wick. After the second build I am fairly pleased with the flavor. I did however experience some difficulty installing the coil due to the clamps moving. I had to reshape the coil after tightening it in place.







FINAL THOUGHTS:

I have to say that I have mixed emotions after testing the Marvos RTA Pod. I did end up with decent results after the second build but do wish that more mesh strips had been included with the pod since my first attempt at building ended up being a failure.

I do like how the base is a quarter turn to remove it but both attempts at building were a bit difficult when trying to install the coil. This was mostly due to the clamps not being spring loaded. If they were then they would have stayed open while trying to insert the coil and feel like having to keep moving the clamp plates open caused my mesh to become misshapen which I believe is why I was getting an atomizer short message on the mod occasionally. I tried the pod first on the Marvos 80s and then switched to the Marvos 60W to make sure it wasn’t a problem with the mod. It seemed like the clamp plates were sticking on the screws and had to use a screwdriver to move the plates back open.

As I mentioned earlier, I wish the tank section would have been made of clear glass rather than the frosted material that the sample I received had. I am used to bottom filling on many pod mods I’ve tried before so am quite used to it but do wish that this one could have been top fill since it is an accessory for the entire Marvos line of pod mods.

I really feel like Freemax had a good idea with this RTA Pod but do feel like there are a few things that could be improved on to make it more user friendly. So there it is as honest as I can be about my experience with the Marvos RTA Pod. I’d like to thank Freemax for finally sending this for review as I’ve been wanting to try it for a while now. Also a big thanks to the readers. Below is a link to the website if you’d like to take a look.


Marvos RTA Pod | Freemax - Taste the Clouds, Feel the Flavors! (freemaxvape.com)

On Jan 1st of 2010, I saw an online ad for an ecig. I did some research and decided I would give it a try. Found Volcano and ordered a kit with the tiny cigalike batt and flavored carts. I will never forget going outside the first morning, early, as I didn't want anyone to see me using it. My first thought was, 'This could actually work.'

Of course, not knowing what I was doing, I had an equipment failure so I bought a pack of cigs and quickly ordered another kit. When I got everything up and running on 1/5, I knew this was it. I had a bit of a panic attack not having cigs around 'just in case' until I realized that if things ever got that desperate, I could go to the store and buy more, even in the middle of the night. Happy to say I never bought another pack nor did I ever smoke even one after that.

It has been an amazing 12 years and I am so thankful for the technology, the helpful people I met along the way. It saddens me to see it being taken away and I think about if I had waited until now to start vaping, I might not have had the opportunity to quit smoking.

Thanks to everyone who went on this journey with me.

Alright, we got 10 different but all tasty flavors of VECEE V4. Wondering which flavor do you like the best? And also, what's your favorite disposable vape flavor that is not shown up above?

Hop in and check out more details we put on: https://www.vecee.com/products/disposable-device/vecee-v4/

Hello everyone

I recently picked up vaping again after several years. I did some mtl the past months but I feel like I'm going to get back in to sub ohm vaping.

I did some research and was really liking the looks of the Uwell Nunchaku 2 and/or Crown 5. (Nunchaku appealed to me because I'm not a great cloud chaser so I dont need crazy watts to feel satisfied, also saving some ejuice along the way is a plus for me)

HOWEVER:
I was about to order the Nunchaku 2, when I found an old Smok TFV8 Big Baby in my closet catching dust, which I totally forgot I still had and hasn't been used in like 4 years.

Now my questing for the experienced vapers around here:

Should I save some bucks and stick with the Big Baby (I would need to get new coils, any recommendations are welcome as I have no clue which ones are compatible these days except for the original standard ones) or just go with a new, more modern tank thats a little more up to date?

In order words: Is the Smok TFV8 Big Baby still worth it in 2022?

Curious about your opinions
Thanks!

So who is going to the Expo that is on 27th to 29th May 22?

Been over 2 years since the last one and they have both dates up on there site for May and October 22.

The new Target 200 gives it all, and leaves you wanting just one more thing – to never leave.

Looking to buy an ohman uno rba if you have one that isn't getting any love anymore.

Sent from my SM-A716U using Tapatalk

This is the first of two parts.

First things first, what is a cycle?

It’s the full discharge of a cell down to its low voltage cutoff, typically 2.5V for a standard li-ion cell, and then a full charge back up to 4.20V. It is the use of the cell at its full capacity rating.

If you remove 3000mAh of charge from a 3000mAh cell, and then recharge it fully, that would be one cycle. If instead you discharge it down to 50%, removing 1500mAh, and then fully charged the cell that would be 1/2 cycle. You would have to do that twice to count as a full cycle.

Two half cycles don’t exactly equal one full cycle since they age the cell differently but it’s close enough for our purposes for now. Theoretically though, two half cycles should age a cell a tiny bit less than one full cycle.

The cycle life rating is the minimum number of these full cycles a cell should deliver, at a certain discharge and charge rate, before the cell’s capacity drops to a certain level. This level is typically between 60%-80% of the original capacity.

For example, a 3000mAh cell with a 300 cycle life rating set at 70% would mean that the cell should still have at least 3000mAh x 70% = 2100mAh of capacity left after being cycled 300 times at the discharge/charge rates mentioned in the datasheet. It might have a little bit more or a lot more capacity left after 300 cycles but it must have at least 70% left if that is the rating.

This point can be used as the end of the cell’s life or the cell can still continue to be used. After dropping to 60%-80% of the cell’s original capacity though many people would be frustrated at having to recharge that cell (or battery pack) more often and would replace the cell/battery pack.

But for some applications, like powerwalls or other low-power energy storage uses, the cell might be cycled many more times to extract as much as possible from the cell to reduce the overall costs of the system.

This all has to be done with an eye on safety though. Continuing to use a cell at well beyond its rated cycle life can mean the cell’s internal resistance has gone up, which makes it hotter during use, and any damage inside the cell is building up too.

Eventually this can lead to cell failure, which can be the cell just self-discharging slowly down to zero volts (ruining the cell) or it can mean the cell short-circuits internally and catches fire (very rare though). A very good battery management system (BMS) is important whenever li-ion cells are used but is critical when cells are used at beyond their rated cycle life.

This BMS can be a few protections built into a vaping device or flashlight, it can be a simple circuit board added to an e-skateboard or e-bike battery pack, or it can be an incredibly sophisticated monitoring, reporting, and protection system for a large energy storage facility.

Let’s look at the cycle life specs of two theoretical cells and compare them…


Example One
Cell A is rated to have at least 70% of its capacity left after 250 cycles at 5A discharge and 1A charge at room temperature.

Cell B is rated to have at least 60% of its capacity left after 200 cycles at 5A discharge and 1A charge at room temperature.

Which cell will last longer?

Cell A will. It will only drop to 70% (or higher) after 250 cycles. Cell B could drop to as low as 60% after only 200 cycles. Cell A is the better choice if cycle life is your priority (assuming it has a high enough current rating).

What’s critical when looking at the cycle life rating of a cell is to note the rate at which the cells are discharged and charged. You cannot directly compare the cycle life ratings of two cells unless that rating was set the same way for both cells!

Example Two
Cell A will deliver at least 300 cycles before dropping to 70% for 10A discharges/4A charges.
Cell B will deliver at least 500 cycles before dropping to 70% for 3A discharges/1A charges.

If we didn’t read how the cycle life rating was set then we might think that Cell B is the better choice since it would deliver at least 500 cycles before dropping to 70% of its original capacity, compared to Cell A only lasting 300 cycles before dropping to 70%.

But Cell A was cycled at a much higher discharge/charge rate than a Cell B. This means that Cell A was being used much harder and that ages the cell faster. We can not directly compare the cycle life ratings for these two cells.

If Cell A was discharged/charged as slowly as Cell B then Cell A might actually last longer. We can’t know though unless the testing was done under the same conditions. This often makes directly comparing the cycle life specs of two cells very difficult.

Part two will be posted soon.

Freemax Maxus Max 168W Pod Mod Kit Review by Z-Lee | e-cigarette-forum.com

Questions, comments, and recommendations are welcome!

Welcome to another one of my overly done reviews where we'll take a look at the new Mesh Pro pod kit - the Maxus Max. I eagerly awaited for this kit to arrive, and anyone that uses Freemax products likely understands why. This is the latest product Freemax has released, which is essentially a compact pod version of the Mesh Pro and M Pro 2 line they've been working on in tandem with the Fireluke-series (my favorite coils).

Regardless of my excitement in receiving this product, I will remain unbias in this review to maintain a fair evaluation against other products with similar functioning. I want to give @Freemax_Jerry a special thank you for making this happen!

First I'll share with you a basic overview of what you'll find on Freemax's website, and then I'll take a deeper look into the aesthetics, features, mod chip, coils, and performance, and then end the review with some of my personal observations and experiences in using this pod kit with a comparative rating at the end.

First, let's take a look at what Freemax has laid out for us in flipbook mode.
Basic Specs:


Dimensions: 43 by 30.9 by 128.5 mm
Weight: 200g
Pod Capacity: 5 mL
Battery: 2x 18650 External Batteries
Output Voltage: 0.7 to 8.4 Volts
Output Wattage: 5 to 168 Watts
Firing Modes: Power, VPC (Variable Power Curve), Bypass, TC (Temperature Control) in SS316, Nickel, and Titanium, and TCR (Temperature Coefficient of Resistance)
Currently Available Coil Resistances (2 More Coils Still to Come): MX1 (0.15Ω), MX2 (0.2Ω), MX3 (0.15Ω), and MX1 (SS316 - 0.12Ω)






Package Contents:

• Freemax Maxus Max 168W Mod
• Freemax Maxus DTL Pod (5 mL)
• MX2 Mesh Coil (0.2Ω - Preinstalled)
• MX1 Mesh Coil (0.15Ω)
• USB-C Type Charging Cable
• Warning Card
• Warranty Card
• User Manual

Colors:

• Black
• Blue
• Gold
• Gunmetal
• Silver

Basic Features:

• New MX Coil Platform
• FM CoilTech 4.0
• IML Screen (in-mold labels - I'll get a little bit into this later)
• Multiple Output Modes
• Maxus DTL Pod
• Side Filling System

FM Chip 2.0 & Protections:

• Over Charge Protection
• Over Discharge Protection
• Short Circuit Protection
• Low Voltage Protection
• Overtime Protection
• Open Circuit Protection
• Overload Protection
• Overheating Protection

(I think you're safe to use this!)

My friend gave me Rose V3, but he lost airflow ring. Of course you can not buy original spare ring ? So I made a new one with one idea in my mind, basically RoseV3 is not mtl so I made AF ring with just one hole 2mm. And there is one other idea, why not bras ring like a spring. So I cut and open ring with hole, and now you can easily turn around AF ring and it did not need O-ring or wire. It clings to the atty body

here it is simple as simple can it be Solid Brass Hex Nuts 3/4” NPT Female Thread
and simple proxxon drill with few attachment's..

Hope you like idea and job..

Dear ECF Friends,

Thanks for your participating~

The Kumiho Model V Pod Kit Giveaway has ended, please feel free to check the winners below, congratulations!!

#123 @Space Cat
#38 @Svanka Lupert
#126 @Gerald Bone


Please DM us below infos to get the prize shipped, thanks.

Name:
Add:
City:
State:
Post Code:
Country:
Tel:
Email address:

-------------------------------------------------------------------------------------------------------------------


Happy New Year!

A brand new year is here, how time flies.

Heathcabin is going to celebrate the new year by giving something different, we will giveaway Kumiho brand new Model V Pod Kit, which can bring a diverse vaping experience with 3 lucky winners in total. In addtion, Healthcabin is now holding a January GEEKDAY 2022 promotion with 20% OFF for all geekvapes. If you are Geekvape fans, don’t miss the chance and save more on your favorite devices!!


Feel free to check the details below.


Kumiho Model V, a polish finished metallic pod system, brings a diverse vaping experience with multiple stunning colors, provides a strong flavor with adjustable airflow. With its innovative vibration interaction, you will know it is ready to vape when the pod connected.




Do you wanna test it? Take the chance to join us and win it home for free.


How To Enter?
Word Chain Game - Take the last letter from the last post and post a new word(about vaping) begins with the taken letter.


Example:
Kumiho
Oxva
Abyss
...
So let's start with: Model V

Note:
1. 3 lucky winners will be randomly selected by random.org on 13th Jan.
2. You must be over 21.
3. Number your entry, for instance: #Post 1, #Post 2...But No Continuous Posts at the same time.
4. Max 10 replies for each participant.


Good luck to you all!

Hi my coil master 521mini is showing a reading of 0.13 ohm for a dual coil setup that is rated as 0.15 ohm. I want to use it in a V-GOD mech mod using Sony VTC-4 Battery. Coils are Steam Train 24 Any idea why it is showing as 0.13 ohm?

Thank you.

Maxus Max 168W Kit by Freemax is one of the smallest dual battery pod mods, which makes full use of the inner space of this device. This Maxus Max 168W Pod Mod Kit is powered by two external 18650 batteries to bring out double endurance and sufficient power with compact size. With Type-C USB Port and 2A Fast Charging function, you can completely get rid of power anxiety.

Hadron Mini DNA100C Kit contains Hadron Mini DNA100C Mod and Aromamizer Supreme V3 RDTA advanced version. It supports single 18650/21700/20700 battery with 100W max power.

Hadron Mini DNA100C Vape Box Mod is compatible with max 25mm diameter tanks, especially match with Aromamizer Supreme V3 RDTA, Aromamizer Classic MTL RTA, and Glaz Mini perfectly. Powered by DNA 100C chipset, it provides Replay/Watts Boost/Accurate Temperature Control mode.

What's more, Hadron Mini DNA100C Combo Kit also features firmware upgrade, type-c fast charging, pass-through. Aromamizer Supreme V3 RDTA Advanced Version has 6ml/7ml e-juice capacity, features single coil/mesh/postless deck, and it is the most flavorful RDTA 25mm.

Please go to best online vape store to choose the vape you like.

You may also like:

Geekvape H45 (Aegis Hero 2) Pod Mod Kit 1400mAh 45W
https://vapesourcing.com/joyetech-widewick-kit.html

$17.99 Rincoe Jellybox Air X Kit




$17.99 Rincoe Jellybox Nano X Kit

Rincoe Jellybox Nano X Kit

Jellybox Nano X Kit utilizes UV 3D print replaceable magnetic panel and fashionable lanyard design. It features innovative airflow control system, auto draw & auto-adjust wattage, you can obtain the most comfortable experience no matter which kind of coil being used. Built with 1000mAh battery, it will provide you all-day vaping and has 10-30W power range. Jellybox Nano X Cartridge can hold 2.8ml e-juice, features side filling and is visible. What's more, it is compatible with Jellybox Nano Coil. And the package contains a mesh 1.0ohm coil for MTL vaping, and a mesh 0.5ohm coil for RDL vaping.

Details:
1. Airflow control system
2. Auto draw & auto-adjust wattage
3. Replacement magnetic 3D panel
4. Compatible with Jellybox Nano Coil
5. 1000mAh battery capacity
6. Type-C charging, LED indicator
7. Fashionable lanyard
8. Side filling & visible cartridge
9. Safety protections: 8S auto cutoff/Over-heating/Low Voltage/Charging/Short-circuit/Over Charging Protection





Jellybox Air X Kit

Jellybox Air X Kit has 1000mAh built-in battery with 10-30W power. 3D print replacement magnetic panels are designed for Jellybox Air X for good texture and strong protection. A fashionable lanyard is applied for Jellybox Air X Kit. Equipped with innovative airflow system, it will provide you the most comfortable vaping experience. In addition, it also features auto draw & auto-adjust wattage. The pod of 3.5ml capacity is visible and features side filling. Jellybox Air X Kit is compatible with Jellybox Nano Coil. And the package contains a mesh 1.0ohm coil for MTL vaping, and a mesh 0.5ohm coil for RDL vaping.

Details:
1. Airflow control system
2. Auto draw & auto-adjust wattage
3. Replacement magnetic 3D panel
4. Compatible with Jellybox Nano Coil
5. 1000mAh battery capacity
6. Type-C charging, LED indicator
7. Fashionable lanyard
8. Side filling & visible cartridge
9. Safety protections: 8S auto cutoff/Over-heating/Low Voltage/Charging/Short-circuit/Over Charging Protection

Is it possible to transform technology into a feeling?

The best way to highlight your vaping and never go unnoticed.

I recently purchased a new tactical flashlight which uses 21700 batteries. I need to find a good, durable case. I would love to find something that attaches to a duty belt setup, but after a week of searching, I don't think that's going to be possible.

I did receive a case with the flashlight, but the battery doesn't even come close to fitting in the thing, even though the case says it's for 21700 batteries (most likely it's for a 20700 battery). Ideally, it should hold two spare batteries, and be durable as they're going to get a lot of use in the field. I see a lot of 'em on Amazon, but I don't want to order a case, only to find they're too small for a 21700 battery. Suggestions?

The SXK BB DNA60W Box Mod clone-Purple is constructed from aluminum with an all-in-one design. BB DNA60W Box Mod by SXK is powered by 1 x 18650 battery (not included) and maximum power output is 60W. The box mod is powered by Evolv DNA 60 chip.
More info BB DNA60W Box Mod
Authentic Evolv DNA60 Chipset;
This is a high quality device by SXK;
Anodized aluminum construction;
60 watts maximum output;
USB port for firmware upgrading, modification and customization;
Minimum Kanthal resistance: 0.16 ohms;
Internal OLED display and menu controls;
Powered by 1 x 18650 battery (not included);
Includes an Nautilus BVC coil adapter;
Delrin drip tip included;
Exceptional build quality;
Limited stock run
This BB Box with Logo

QUICK LINK,click here>>Buy SXK BB Style 60W All-in-One VW Box Mod Vape Kit w/ USB Port Purple