eGo ONE tank series – CLR coil
- Thread starter pufZeppelin
- Start date
- th_trl_thread_readers 0
- Status
WOW !
so I just got BURNT by the screwed up system
I ordered >$200 worth of ejuice Friday, then got an email this morning saying the order is on hold until
I email a copy of my drivers license to them...
no way in hell will I allow my ID to float around www
"sorry, just cancel, refund my order" -- "O.K. sir"
so I just got BURNT by the screwed up system
I ordered >$200 worth of ejuice Friday, then got an email this morning saying the order is on hold until
I email a copy of my drivers license to them...
no way in hell will I allow my ID to float around www
"sorry, just cancel, refund my order" -- "O.K. sir"
so I just got BURNT by the screwed up system
I ordered >$200 worth of ejuice Friday, then got an email this morning saying the order is on hold until
I email a copy of my drivers license to them...
I usually check this list before I order from a site online ("Unknown" means ordering is hassle-free):
Vendor Age Verification Procedure List
..
Last edited:
Ty for posting this. My order after 8/8 went through fine, I guess that's a recent thing. Bye bye Heartland. That bites after all the shopping you did! If they would just put the info on the first page, or at least prior to registration and ordering.WOW !
so I just got BURNT by the screwed up system
I ordered >$200 worth of ejuice Friday, then got an email this morning saying the order is on hold until
I email a copy of my drivers license to them...
no way in hell will I allow my ID to float around www
"sorry, just cancel, refund my order" -- "O.K. sir"
View attachment 617565
yepper, was a shock - first time I've ever been turned down
was planning on most of that for gifts...
and it seemed like the young lady on the phone (very polite) wasn't all that concerned about
my canceling a large order - kinda care free - - " ok then, Thank You "
not sure where the blame falls - not sure if Heartland Vapes could handle it in a different way ??
an Adult delivery signature is all that's needed... IMO
I don't have a problem trying to stop minors from acquiring nicotine...
oh well, life goes on...
was planning on most of that for gifts...
and it seemed like the young lady on the phone (very polite) wasn't all that concerned about
my canceling a large order - kinda care free - - " ok then, Thank You "
not sure where the blame falls - not sure if Heartland Vapes could handle it in a different way ??
an Adult delivery signature is all that's needed... IMO
I don't have a problem trying to stop minors from acquiring nicotine...
oh well, life goes on...
I have been having trouble with the coils wicking. Get a harsh, burnt vape every once in while after using a coil
for a couple of days. I use kanthal with rayon. It was driving me nuts!
Finally decided to try some different approaches to getting the wick to soak that juice up.
First test was with the current wick I had been having trouble with, decided to push the wick into
the coil body...I know, sounds like a bad joke. Futzed with the wick until it was all in the coil body on
both sides. Put it back together and fired it up. Worked great! Raised the watts from 14 to 20 to see if
I could get it to vape ahead of the wicking...kept vaping nicely! But it was too warm for me.
Rolled a new coil to try it again, works great for the second time.
Here's what I did to the wick:
I trimmed as close as possible to the body and then pushed the wicking inside the coil body.
Here's what it looks like with the cap on:
Thought I would throw this out there and see if any other recoilers have the same experience with pushing their wick into the coil body.
'Cause a wet wick makes for a happy Vaper!
for a couple of days. I use kanthal with rayon. It was driving me nuts!
Finally decided to try some different approaches to getting the wick to soak that juice up.
First test was with the current wick I had been having trouble with, decided to push the wick into
the coil body...I know, sounds like a bad joke. Futzed with the wick until it was all in the coil body on
both sides. Put it back together and fired it up. Worked great! Raised the watts from 14 to 20 to see if
I could get it to vape ahead of the wicking...kept vaping nicely! But it was too warm for me.
Rolled a new coil to try it again, works great for the second time.
Here's what I did to the wick:
I trimmed as close as possible to the body and then pushed the wicking inside the coil body.
Here's what it looks like with the cap on:
Thought I would throw this out there and see if any other recoilers have the same experience with pushing their wick into the coil body.
'Cause a wet wick makes for a happy Vaper!
I have been having trouble with the coils wicking. Get a harsh, burnt vape every once in while after using a coil
for a couple of days. I use kanthal with rayon. It was driving me nuts!
Finally decided to try some different approaches to getting the wick to soak that juice up.
First test was with the current wick I had been having trouble with, decided to push the wick into
the coil body...I know, sounds like a bad joke. Futzed with the wick until it was all in the coil body on
both sides. Put it back together and fired it up. Worked great! Raised the watts from 14 to 20 to see if
I could get it to vape ahead of the wicking...kept vaping nicely! But it was too warm for me.
Rolled a new coil to try it again, works great for the second time.
Here's what I did to the wick:
View attachment 618177
I trimmed as close as possible to the body and then pushed the wicking inside the coil body.
Here's what it looks like with the cap on:
View attachment 618179
Thought I would throw this out there and see if any other recoilers have the same experience with pushing their wick into the coil body.
'Cause a wet wick makes for a happy Vaper!
I DON'T actually push the wick back into the body
but I learned that it works better for me if I keep them VERY short...
but I learned that it works better for me if I keep them VERY short...
That's what I was doing too...still had issues. Considering a coil lasts me at least a week, it's worth the trouble.I DON'T actually push the wick back into the body
but I learned that it works better for me if I keep them VERY short...
ya know, after I cut it off CLOSE - I poke it around with a toothpick/dental tool
what I try to do is be sure the BOTTOM of the square hole is absolutely covered or packed with wick...
what ever happened with the " flavor wick " you were trying across the top ??
what I try to do is be sure the BOTTOM of the square hole is absolutely covered or packed with wick...
what ever happened with the " flavor wick " you were trying across the top ??
I used the little flavor wick with TC and it worked great, didn't seem to make much difference with kanthal.
Throw your hat over the fence, I think I settled on the flavor wick being 1/4 the size of the regular wick.
yepper, my clr's have been working great but I would like to try it and will sometime, if I can remember...
rayon / 3.0mm I.D. SS / 1.0Ω / 25w / 320° is about my average
rayon / 3.0mm I.D. SS / 1.0Ω / 25w / 320° is about my average
- Status
Similar threads
- Locked
- Locked
