ECF Registered advertiser

  1. Take part in the #WeAreVapor campaign

    Dear Guest, 

    The  #WeAreVapor campaign has just launched and needs your help. This is a massive push to get vapers and vapor businesses visible, and make Congress aware of the Cole-Bishop amendment. It is being organised by the Vapor Technology Association. 

    Please take a minute of your time to take a look at the site to see how you can get involved. 

    Thanks!

    Dismiss Notice

Important !!!!!! V3 16340 set

Discussion in 'Eastmall-ecigarette' started by Di, Nov 2, 2011.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. Di

    Di ECF Guru ECF Veteran

    Oct 30, 2008
    *Australia*
    the V3 16340 set could not use any other atomizer but the HV atomizer ,
    if they use other atomizer, it will not work
    this is because of the PCB we put on the 16340 battery to protect it
     
    Di, Nov 2, 2011
    Di, Nov 2, 2011
    #1
    ECF Registered advertiser
  2. Nicko

    Nicko Super Member ECF Veteran

    Dec 1, 2010
    China
    I don't think you are going to sell many of these.
     
    Nicko, Nov 2, 2011
    Nicko, Nov 2, 2011
    #2
  3. Di

    Di ECF Guru ECF Veteran

    Oct 30, 2008
    *Australia*
    actually we will,

    one of the guys came in and said that ----
    any atty that was of the right ohms wold do the job--
    he gave some specs too,
    so as long as it is of the HV range of ohms, and does not trip the
    safety PCB -- it would be fine --------

    quoted from * Beavert *

    I don't want to speak for anyone else ,but any atty or carto of an appropiate ohm rating should work. For instance something like a 1.5 ohm atty wouldn't work at all. That would draw 24 watts and 4 amps way too much. It would either pop your atty nearly instantly or hopefully activate the protection circuit on the batteries. Where as an 4ohm atty will provide a much more sane 9 watts and 1.5 amps. In short it doesn't matter which device you use when your using any high voltage device then you must select an atty or carto in the correct ohm range.
     
    Di, Nov 3, 2011
    Di, Nov 3, 2011
    #3
  4. Nicko

    Nicko Super Member ECF Veteran

    Dec 1, 2010
    China
    Ok. Actually I read your announcement, and then emailed Selina and said I don't want it.

    I will email her again and tell her to send it. Thanks.
     
    Nicko, Nov 3, 2011
    Nicko, Nov 3, 2011
    #4
  5. Di

    Di ECF Guru ECF Veteran

    Oct 30, 2008
    *Australia*
    thanks Nicko,

    there is often another solution to any problem

    many of our members are very helpful to each other
    and often they will give advice which can help us all.
     
    Di, Nov 4, 2011
    Di, Nov 4, 2011
    #5
  6. Nicko

    Nicko Super Member ECF Veteran

    Dec 1, 2010
    China
    I got my Indulgence in the mail today.

    If anyone is considering the 6V, please be aware of two things.

    1. The charger can only charge one battery at a time. It is not long enough to hold two 3V batteries. I'm lucky I ordered an extra charger.

    2. Choosing the 6V option limits your choice of atty or carto. The atty that came with the kit works, but none of my others work on this. I took the advice offered here and tried my 3 ohm tank, but that didn't work either. Other users may have better luck.

    There's nothing wrong with the Indulgence. I'm using it now with an 18650 3.7V battery and all my favorite cartos are performing well.
     
    Nicko, Nov 10, 2011
    Nicko, Nov 10, 2011
    #6
  7. humpty

    humpty Reviewer / Blogger ECF Veteran

    Jun 23, 2010
    HK
    Most protected batts prevent a 'short' by detecting for 'over-current', i.e if the current is too high, it'll cut.
    (some of them do this by measuring the voltage drop across an internal resistor)

    The same rules apply to most HV mods; HV atty current will not hit that high-current mark, LR atties will.
     
    humpty, Nov 10, 2011
    humpty, Nov 10, 2011
    #7
  8. Davidyang

    Davidyang Unregistered Supplier ECF Veteran

    Aug 3, 2008
    China
    Hi NiCKO,

    Thanks for your support, for the 6V 16340 starter kit, We finally have a new dual charger especially for 3.2V battery now.
     
    Davidyang, Nov 11, 2011
    Davidyang, Nov 11, 2011
    #8
  9. Davidyang

    Davidyang Unregistered Supplier ECF Veteran

    Aug 3, 2008
    China
    Thanks Humpty, you helped a lot with the description:p
     
    Davidyang, Nov 11, 2011
    Davidyang, Nov 11, 2011
    #9
Thread Status:
Not open for further replies.

Share This Page

ECF Registered advertiser