SMOK_TFV4
Purchased TFV4 through the online !
Product composition
tank with a 0.2 Ohm coil
extra O-Ring
Lock-Ring
Product specifications
Diameter : 24mm
Liquid capacity : 5.0ml
Resistance : 0.2 oHm
Material : Stainless steel, Pyrex glass
Weight : 92g
Thread type : 510
Overall atomizer image
Drip tip airholes in 4 locations
And then another 4 airholes located at the bottom (8 total).
Unlike Atlantis or Subtank types with stopper making tick-tock sounds when adjusting the airflow, this airhole slides smoothly.
Dip tip area
.It has another channels to prevent vapor leaking through airhole
Inside the tube is designed to pass the vaporized liquid, and outside channel passes the external air.
An arrow at the top of the tank indicates how you should open up the liquid filling area.
Top-caps fit each other like teeth.
Top part can be opened by pushing the part in the direction where arrow indicates
Liquid injection should be from holed rubber area, not from the center
You can close in vice versa
Now, we separate the drip-tip
It is 510 type
I disassembled the device like this.. simply hold the pyrex glass and unscrew the top part and driptip.
Upper coil area and Top-cap are designed to fit in thread.
Vaporized liquid from the coil be inhaled into your mouth like a real dripper
I separated the Glass tube, now the top part of the tank is now completely disassembled.
Took out the coil cylinder as well.
Now this is it for disassembling the device.
Compare to other products, this coil is much bigger thanks to the triple coil type structure.
Now you can see the coil adjoining area.
It consists of spring pin, and we eliminate unnecessary parts to ensure maximum airflow
As you can see in this picture, it has a large hole, and this hole also contains 4 holes in different locations.
Thanks to its large size, it ensures airflows pretty well.
This is the picture showing inside of 0.2 oHm triple coil
The coil’s made with a separate structure, so that short can be prevented.
We fold cottons with vertical coils from the outside
0.15ohm coils has 4 coils (quadra)
Think of it like triple coil is like a 3 engines vehicle, and quad coil consists of 4 engine vehicle
0.15 ohm has greater Atomization capacity than 0.2 ohm of course.
Liquid can be filled to the hole showing in the picture.
As you can see, 75w can output 3.96V.
With a MOD using only one 18650 battery cell, the tank’s full potential cannot be reached unfortunately.
If you wish to use 100% of its capacity, you should have a MOD with an output over 100w.
Advantage
You can experience great vapor productions.
Those tanks with 0.5 ohm coils, they can bring out some vapor productions, but not as much as dripper devices. But this tank with 0.15 ohm coils, can make vapor productions that can match those drippers.
Upper liquid filling without leakages
We folded cotton of the coil tightly so we can expect that leakage will not happen without any necessary actions. Top cap is designed as siding door for upper injection so it can be quite convenient for users..
Drip-tip air-hole can satisfy your personalized favor
There air people who prefer warn vapors, and there are people who prefer cold vapors when vaping.
TFV4 can satisfy for both types of users. If someone want warm type steam, then you can simply close drip tip air-hole and vape.
In other words, if you want warm types steam, please open the drip tip air-hole and vape.
Disadvantage
The device gets heated too much.
We experienced that my atomizer became heated even though we only vaped several times with 75W 3.96V.
For the first time, my SX Mini M class was getting heated.
We can expect the fact that amount of electricity will be too severe because resistance of coil is low, but getting too much heat is certainly a disadvantage.
Flavor is less tasty than its atomization capacity
.
As I vaped, I felt that flavour was weak.
I wonder how this might be happening with all the triple & vertical type coils, so I tried using it with the driptip air-hole closed, but again the flavour was quite weak.
Purchased TFV4 through the online !
Product composition
tank with a 0.2 Ohm coil
extra O-Ring
Lock-Ring
Product specifications
Diameter : 24mm
Liquid capacity : 5.0ml
Resistance : 0.2 oHm
Material : Stainless steel, Pyrex glass
Weight : 92g
Thread type : 510
Overall atomizer image
Drip tip airholes in 4 locations
And then another 4 airholes located at the bottom (8 total).
Unlike Atlantis or Subtank types with stopper making tick-tock sounds when adjusting the airflow, this airhole slides smoothly.
Dip tip area
.It has another channels to prevent vapor leaking through airhole
Inside the tube is designed to pass the vaporized liquid, and outside channel passes the external air.
An arrow at the top of the tank indicates how you should open up the liquid filling area.
Top-caps fit each other like teeth.
Top part can be opened by pushing the part in the direction where arrow indicates
Liquid injection should be from holed rubber area, not from the center
You can close in vice versa
Now, we separate the drip-tip
It is 510 type
I disassembled the device like this.. simply hold the pyrex glass and unscrew the top part and driptip.
Upper coil area and Top-cap are designed to fit in thread.
Vaporized liquid from the coil be inhaled into your mouth like a real dripper
I separated the Glass tube, now the top part of the tank is now completely disassembled.
Took out the coil cylinder as well.
Now this is it for disassembling the device.
Compare to other products, this coil is much bigger thanks to the triple coil type structure.
Now you can see the coil adjoining area.
It consists of spring pin, and we eliminate unnecessary parts to ensure maximum airflow
As you can see in this picture, it has a large hole, and this hole also contains 4 holes in different locations.
Thanks to its large size, it ensures airflows pretty well.
This is the picture showing inside of 0.2 oHm triple coil
The coil’s made with a separate structure, so that short can be prevented.
We fold cottons with vertical coils from the outside
0.15ohm coils has 4 coils (quadra)
Think of it like triple coil is like a 3 engines vehicle, and quad coil consists of 4 engine vehicle
0.15 ohm has greater Atomization capacity than 0.2 ohm of course.
Liquid can be filled to the hole showing in the picture.
As you can see, 75w can output 3.96V.
With a MOD using only one 18650 battery cell, the tank’s full potential cannot be reached unfortunately.
If you wish to use 100% of its capacity, you should have a MOD with an output over 100w.
Advantage
You can experience great vapor productions.
Those tanks with 0.5 ohm coils, they can bring out some vapor productions, but not as much as dripper devices. But this tank with 0.15 ohm coils, can make vapor productions that can match those drippers.
Upper liquid filling without leakages
We folded cotton of the coil tightly so we can expect that leakage will not happen without any necessary actions. Top cap is designed as siding door for upper injection so it can be quite convenient for users..
Drip-tip air-hole can satisfy your personalized favor
There air people who prefer warn vapors, and there are people who prefer cold vapors when vaping.
TFV4 can satisfy for both types of users. If someone want warm type steam, then you can simply close drip tip air-hole and vape.
In other words, if you want warm types steam, please open the drip tip air-hole and vape.
Disadvantage
The device gets heated too much.
We experienced that my atomizer became heated even though we only vaped several times with 75W 3.96V.
For the first time, my SX Mini M class was getting heated.
We can expect the fact that amount of electricity will be too severe because resistance of coil is low, but getting too much heat is certainly a disadvantage.
Flavor is less tasty than its atomization capacity
.
As I vaped, I felt that flavour was weak.
I wonder how this might be happening with all the triple & vertical type coils, so I tried using it with the driptip air-hole closed, but again the flavour was quite weak.