Search results

  1. Imfallen_Angel

    Eleaf ikonn 220 charging warm ?

    if you're charging overnight, get a a good brand charging brick, but stay with a 1A model... I know that most company hype the quick charging at 2A, but it's better for the batteries to be charged slowly. A bit warm is absolutely normal, cell phones and anything else that you charge will warm...
  2. Imfallen_Angel

    Eleaf iKonn 220, quick review and issue resolved

    Just a quick note about this mod. I've got 3 of them at my house now... and after a few weeks I can say that it's a great mod, feels great to hold, very small as it's barely larger than the 2 batteries it holds. Battery life is very decent and better than just about every other mod I have...
  3. Imfallen_Angel

    resistance ranges

    It's a question of the physics...between the voltage, and the metal used (and it's range), it's a safety limit that manufacturers have worked out. More info here: (extract) Results The minimum resistance you should use is typically determined by the PV's current (amp) limit. The maximum...
  4. Imfallen_Angel

    resistance ranges

    Physics.... Higher the resistance, the more you'd need a massive coil made of very fine wire that no standard deck could handle. example: for 3ohms: 316L SS, 28 gauge, 3mm = 28 wraps For TC to work right, this would need to be spaced... so I'd estimate a 40mm or larger deck. The metal...
  5. Imfallen_Angel

    Temperature control

    Checking one single coil deck RTA I have in use now, and I've been going with around 0.5ohms for single coils, so around 7-8 wraps.
  6. Imfallen_Angel

    Temperature control

    I've yet to find an actual cut-off, but by building as large a coil as I can fit on a deck for single coil decks, it's been working fine since. My regular type would be 26 or 28 gauge, from 2.5 to 3.5 mm width, which usually gives me 0.3 and higher ohms. I no longer aim for a particular ohm...
  7. Imfallen_Angel

    Need Help Coil Building

    Then you need to learn a LOT... More wattage, lower ohms does not mean "cloudzzzzz", it means that the person is clueless about building properly. It's about wire surface, it's about balance...and also, more cloudzzzz does not mean more flavour. Build right, you can fog a room up with a coil...
  8. Imfallen_Angel

    0.5 coil became 0.81 after re-wicking. Dangerous?

    Just from re-wicking? It shouldn't have... You should remove the wick, test your coil to ensure that you don't have hot spots, measure it again to see what the reading it. Wicking should not change the resistance, so either you've moved the wraps a bit and something's touching wrong, the...
  9. Imfallen_Angel

    eleaf istick lifespan

    As per my previous post, I'm indicating where the resistance does impact the function of a mod. It's not about disagreeing, it's about proper info, stating half the info isn't providing the full story. Anyways, I'm done.... I simply provided clarifications, and it's just getting dragged into...
  10. Imfallen_Angel

    What's the deal with steeping?

    As per the other thread where you're "stalking me" today (did your buddies call you in to assist with the harassment?)... I'm providing proper info, knowledge and such to assist others.... what are you doing? Personal and childish attacks.
  11. Imfallen_Angel

    eleaf istick lifespan

    It's nothing about "disagreeing", it's about correct information, ensuring that newbies get proper information towards safety. Disprove what I just stated if you can... good luck with that, and no moving the goal posts either, but I doubt that you'll resist. At least you're showing to be...
  12. Imfallen_Angel

    What's the deal with steeping?

    o_O:rolleyes: Considering that you're on a quest to try and prove something from thread to thread, I say that you're just getting petty at this point. I never said that you can't DIY without a mixing device, simply that it has many advantages. Advantages that makes it absolutely worth while...
  13. Imfallen_Angel

    eleaf istick lifespan

    :rolleyes: Mooch's comments involves high drain batteries with coils that have a decent range. I you want to keep this joke going, just go read all the sites of the manufacturers that state clearly that you have to use proper batteries (high drain, 20-25A are highly recommended). If the ohms...
  14. Imfallen_Angel

    eleaf istick lifespan

    I had a 30W istick a while back that simply had less and less life, and at the end could barely last a 1/2 hour's worth of vaping. We followed it with a 50W to replace it, which lasted a good 6 months until we got a few Innokin Coolfire, but by then I started to get mods that were 18650...
  15. Imfallen_Angel

    eleaf istick lifespan

    You know.. over and over, you and few others prove that you are arrogant, don't have a proper understanding about a lot of things and do nothing more than childish attacks. It's petty and sad. The ohm will affect a regulated mod in multiple ways, from the draw, to the limitations of the wattage...
  16. Imfallen_Angel

    eleaf istick lifespan

    I gather that english is simply not your first language... I stated LOW DRAIN. I also stated "In that video" above that someone linked, about resoldering a battery in a disposable mod. I don't think that you are able to read correctly. And yes, the ohms on regulated mods do matter. It's...
  17. Imfallen_Angel

    New to you

    For notch coils... to be honest, I never bothered, reviews are just too poor on them.
  18. Imfallen_Angel

    New to you

    And also, the more wire and better balanced approach you take, the more vapor you can make... Vapor production is better with more wire surface (so thinner wire is better, to an extent). At this time, the best results I get is with 26gauge SS, and with dual coil decks. Note that the tank...
  19. Imfallen_Angel

    New to you

    For a single, you're kinda stuck having to make a large coil, try and switch to 28 gauge if you can. For SS troubles, check my blog, I explain in it that for single coils to be read well, you need to have a certain amount of wire mass for it to register well. As you are going with TC, stop...
  20. Imfallen_Angel

    New to you

    First: Get off the low ohms bandwagon. You should stick to 0.2 ohms at an absolute minimum and higher. Under 0.2, you can end up putting your batteries at risk, and it absolutely does not make anything "better". With proper builds and balanced settings, you can get great results at a safer...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu