Search results

I recently started three new batches of PG soaks for maceration of pipe tobaccos after getting away from it for a few years. Previously I used an Aeropress with one of these two filters after the first press with the Aeropress filter: Ahlstrom Quantitative Filter Paper, No 74, 7cm Diameter...

Does anyone have any experience with this RTA? Can it be built with single coil if I want to vape it with my Sigelei V5 that won't sub-ohm? Does it do well in that configuration? Thanks.

I recently switched all of my Kanger Protank II's over to the Air Flow Control 3.0. Great modification, but I've had two of them quit working on me in the last two months. They just quit making connection to the battery (Sigelei Z-Max V-5). I suspect the post is receding in the body of it and...

I'm getting ready to extract some pipe tobaccos from cold maceration and I am thinking I'm going to use the Aeropress to filter them. The first filtering will be with one or two of the Aeropress filters (I like the idea of sqeezing all that I can out of the tobacco!) and then with a 2 micron...

I was going to post this in the New Members Forum, but apparently I can't post there any more... I thought it would be good for new members to hear a success story of sorts and maybe absorb some of what got me here, both good and bad. Oh well, I hope they venture out of the New Members area. I...

Well, maybe love is a bit strong, but I sure like and appreciate him a lot! He initially mentioned trying vaping to quit smoking, and was very supportive of it. He said he is firmly convinced that it is a significant reduction in possible harm. He had seen over the years that nothing else worked...

Recently Passed (Due to Legislative Override of Veto) and signed into law in Missouri: SENATE BILL NO. 841 It establishes, in the definition section that electronic cigarettes are not to be classified as tobacco products. This saves them from taxes that are levied on tobacco products! The...

I tried doing a search but didn't come up with this specific topic, but a wide variety of topics, some related, others not. So I thought it would be a good one to have out there for others with this specific question: How do you clean and store your syringes after mixing? That would include one...

When I was playing around with the eJuice Me Up Calculator, getting ready to start up my first batch of DIY juices, I tried printing to my copy of MS Office 2010 One Note and it crashed. I did some research and found that the 2013 version doesn't crash when printing to it and it's available for...

I have everything else I need for now and I just placed my first flavor orders yesterday: EcigExpress Ry1 Flavoring by Hangsen Flue-Cured Tobacco Flavoring by Hangsen 7 Leaves Tobacco by FlavourArt Layton Blend Tobacco by FlavourArt Flavor Apprentice Black Honey Flavor Tobacco Flavor...

Like the title says, do you folks buy the Ethol Maltol (EM) crystals and then mix it (with what?), or do you buy the 10% solution like Wizard Labs (WL) has? See what I did there? I propose a DIY Style Book that says you spell the full name with the abbreviation in parenthesis for the first...

I'm new to the RBA/RDA world so bear with me if this is a dumb question. I recently purchased an IGo W4 and built a coil or two. When I tried it on my MVP V2, despite screwing it all of the way down (ego threading), it apparently wasn't making contact because I got "NON" for the reading. I tried...

I recently purchase the Igo W4 to try out dripping. I've been building coils for my Protanks so the coil build wasn't hard. Wound up with 2.7 but my target is lower, say 1.8 or so. It was a little tricky in setting the coil up as the Igo is pretty small. I've included a photo of the build and I...

Looking to start DIY and was curious if anyone approached mixing by starting with a given level of nicotine in a PG/VG solution and added the flavors to get a final percentage that is close to a target level of nicotine. In other words, if I currently vape 24 mg nicotine and premix a PG/VG mix...

I think I have this correct but wanted to check to see. Is where I have the arrows pointing in the photo the places to place the probes from my meter to check the resistance? I want to build some coils and I don't have a mod to check them, but I have a decent meter. I've successfully...

I think I have this correct but wanted to check to see. Is where I have the arrows pointing in the photo the places to place the probes from my meter to check the resistance? I want to build some coils and I don't have a mod to check them. I've successfully converted the Kanger heads to...

At the end of the year I wrote my US Senator, Claire McCaskill, and urged her to monitor the FDA's deeming regulation of E-Cigs. Below is the body of my letter and her response. Take what you will from it. There's no real commitment in her response, and I think she felt she was throwing me a...

Pre-wrapped coils from Fasttech: $2.16 Pre-Coiled Welded Wires - NR-R-NR (50-Pack) 50-pack - 32 AWG / 1.5ohm / 30*30mm at FastTech - Worldwide Free Shipping At 4 cents a piece including shipping, it's tempting to try in my Kanger Protank II Mini. Disclaimer: I know it's probably better to wrap...

I didn't see a model specific forum for this so I thought I'd ask here. Can someone tell me the difference between the "Round Top" and the "Flat Top" of this model? Possible use with a Protank II Mini or a Protank II? Also, anyone have any experience with the "Black Chrome" one. Does the finish...

I finished dinner tonight and sat down with my E-Go C-Twist and a Pro Tank Mini with a full tank of a mixture I made of some local juice I bought at a local B&M called "Elite Cig" and about 25% of a Double Ry4 and had some good vapes. The mixture has a good throat hit but is mellow and produces...