The Screen flickers and shows scrambled symbols. Sometimes the information such as ohms and wattage will be just barely visible but only when I'm firing the device. Other times the screen won't come on at all. Whatever the screen displays it usually always goes blank the second I let go of the...
hey,
I just received the pre-cut 1.8Ohm resistance - no resistance wire that I ordered. I just wrapped it and cut it and my V3 read it at 1.8Ohm right away. Vapes good so far. So simple and easy I think I'll be using this from now on. Still not sure what what was going on with the 32 gauge...
Hey,
I was having some trouble rebuilding protank heads with 32 gauge kanthal including burnt grommets, shorts, overheating etc. Someone on here recommended I try some resistance - no resistance - resistance wire. I just received 50 pre-cut 1.8Ohm wires in the post. The length is about 2inch...
It's got me confused anyway. I just ordered some pre-cut 1.8Ohm resistance - no resistance wire, so hopefully that will work. I feel there is some issue with the current/insulator or - like you said - amperage, that the regular eGo is simply ill-equipped to detect. Perhaps that's why the regular...
I don't feel like it's a short due to crossed wires, etc. I have rebuilt tens today that all behave the same... plus, I am quite methodical about my coils being just right. It seems like something to do with the behaviour between the wire and the insulator. But I have no idea if it would or how...
Thanks for the suggestions.
I think the issue could be the insulators. On closer inspection, it seems most of the ones I have been using are burnt. Although that doesn't explain why a rebuild with a fresh insulator also reads low ohms and won't fire. Unless there is just too much current going...
Hey,
I've been rebuilding Protank heads for a while, but I've never had any way to check Ohms until recently. I used 5 wraps of 32 gauge Kanthal around 2.5mm Silica with a needle or around a cocktail stick for a cotton build. I've been vaping this build for a couple months on basic Ego...
Thanks,
I did notice the difference in length between the two heads and did think perhaps the protank heads may not reach the center pipe on the Evod 2. Bought a couple of the original Evods instead. I just needed something small and simple that takes rebuilt protank heads. The New Evod 2 and...
Thanks for the replies and suggestions,
I started reducing the amount of flavour wick bit-by-bit and was getting less and less dry hits. May have to remove more though, as the head I have in now is still dry-hitting occasionally. It definitely feels like it happens when the flavour wick isn't...
Hey,
I'm looking to buy the Evod 2 but I have no interest in dual coils. I currently rebuild single coil Protank heads to use in my Unitank. I would like to know if I can use these single coil Protank heads in the Evod 2? If so, is there any notable differences such as change in air flow or...
Hey,
I use .32 gauge kanthal A1 and 2.5mm VoodooWool (silica) I've been experimenting with different builds on kanger heads and feel I can hit the resistance I seek (2.5) with 6 wraps of the .32 Kanthal.
The problem is that without a flavour wick; I instantly get persistent gurgling. If I add...
Thanks. The MVP 2 does sound appealing. The whole box mod thing puts me of a little though. I just imagine it would feel somewhat awkward and unwieldy in hand.
Hey,
I'm looking to buy a new mod. It needs to be VV and have an ohm checker. Other than that, I just want something simple that performs well with as little hassle as possible. Doesn't need to be flashy.
I previously owned a 1100mAH Ego-style and a Tornado RCS (Battery mod with pass-through...
Chain vape for 20 mins - if you get a headache or feel light-headed - lower the strength. I chain vape 18mg for hours and just feel a bit spaced out at worst.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.