6volt on reo grand

[Rudy956]

I'm going to purchase a reo grand when they go up for sale my question is: I bought 2 tenergy rca 123a batteries (3volts) Can i use a 1.5 ohm attomizer with a reo grand at 6v or do i have to use a specific attomizer or cartomizer? Sorry if its a dumb questions..

thanks,
Rudy

 

[davelog]

I use 1.5's with my 5v setup, if that helps.

 

[Rudy956]

I use 1.5's with my 5v setup, if that helps.

Have you ever tried it at 6v?

 

[davelog]

I tried 6v in a different mod, and it was too hot for my tastes. Never tried in the Grand. The 4.8v batteries are right there for me, the flavor and volume with less heat.

 

[Rhapsodies Fire]

It really depends on personal preference. Some like to use 2.0Ω and others like it at 3.0Ω. If you decide to go the 2.0Ω route, just be sure to keep your atty wet.

 

[Mudflap]

I'm going to purchase a reo grand when they go up for sale my question is: I bought 2 tenergy rca 123a batteries (3volts) Can i use a 1.5 ohm attomizer with a reo grand at 6v or do i have to use a specific attomizer or cartomizer? Sorry if its a dumb questions..

thanks,
Rudy

Howdy, Rudy. Did you get my P.M. earlier today?

I'd start with a 2.5 ohm atomizer at 6 volts.

 

[bowhunterr2001]

I use a 2.2Ohm 510 atty @6volts in my Grand.. 2 Tenergy RCR123A 750Mah stacked, It works great!!

 

[Rudy956]

Howdy, Rudy. Did you get my P.M. earlier today?

I'd start with a 2.5 ohm atomizer at 6 volts.

Yes i did but amazon wont refund me I'm stuck with these batteries... The bad thing is that the batteries are the li-lons not the lifepo4

 

[Mudflap]

Yes i did but amazon wont refund me I'm stuck with these batteries... The bad thing is that the batteries are the li-lons not the lifepo4

Well, be aware they have a PCB on those batteries and if the resistance of the atty/carto you use is too low, it will probably trip the circuit. Just pop them in your charger and plug it in to reset them. Good luck!

 

[pmoraldo]

I use 1.5's with my 5v setup, if that helps.

Really wow I would think you'd POP an lr at 5v especially a 1.5

 

[davelog]

Haven't yet! I keep it nice and juicy, though. I'm sure that helps.

 

[ufo]

Depends by the brand and type of the atoms.

For example.
With the 510, for 6v, I use 3 ohm with Cisco. With the IKV 2.5 ohms. With Joye, SLB, EM... also 2.2-2.3 ohms to 2,5ohm, because I noticed how each brand has a different performance (so a 3ohm on a cisco has, more or less, the same hit a SLB 2.3 ohm, because the cisco are much more reactive)

With the 306, however, I use only cisco and IKV 2.5 and 3 ohms.

The matter is even more complicated if we consider the 801, the 901 or the various types of cartoms ..... I'd prefer not go into details, otherwise I risk of writing a post of 3 pages

 

[FunkyVapes]

Just for giggles I tossed 2 freshly charged Tenergy 3.0V 123 rca batteries on my grand with a 1.5Ω Joye 510 atty. I Put lots of juice right onto the atty and it seriously burnt the hell out of it. I usually go 2.5Ω at the absolute lowest on my GGTS at 6V.

 

[pmoraldo]

Tried the 1.7 resurrector at 5v on my grand and it was some pretty hot vape