AC9 Genesis atomizer available to the public!!

[tenshi]

Hey guys, ive recently got my hands on an AC9 V1.3 from C9V here in the UK, and its leaking quite a bit from the 510 its got the black screw in top insulator and a white delrin at the bottom, center post came setup with spring-washer-spring also has that funky clear custom drip tip (the oring is a bit big and a chunk is missing from it now) - Is there anything ive possibly done wrong, only thing i did when i got it was take it apart and clean and put back in the same order as i took it apart.

hmm I upgraded my old ac9 and have the new one (v1.3) and have been vaping on both, no leaks... Hmm, should go from bottom up: white delrin - tank - black delrin -washer - spring - washer - screw. Got mine at vapinaze.

 

[Viluxia]

Update - After some advice from where i bought it from, i tweaked the black delrin very gently with some needle nose pliers and its been almost 4 hours and its bone dry, panic over one happy AC9 vaper.

 

[arh32]

1.3 will be nice.

 

[pekkapoika77]

Ac9 arrived, thank you Vapinaze

 

[Jesse13]

Sweet combo, that's what i have in mind for my own set up. Still need a caravela though

 

[tenshi]

- Poldiac with AC9 filled with Khlorine (yummy)

 

[neoexodus]

- Poldiac with AC9 filled with Khlorine (yummy)

What is wrong with you?!? Put your pants on!! You're in public!!

 

[tenshi]

What is wrong with you?!? Put your pants on!! You're in public!!

haha

 

[Vcoupe]

Love my ac9. I polished the upper bevel into the drip tip and properly brushed the body

 

[tenshi]

Love my ac9. I polished the upper bevel into the drip tip and properly brushed the body

That's beautiful vcoupe

 

[cruxfm]

How does the AC9 airhole compared to a Z-atty?

 

[tenshi]

How does the AC9 airhole compared to a Z-atty?

Z atty (I think) is 1/16'' so ~1.59 mm and AC9 is 1.5 mm

 

[forg1vn]

Z atty (I think) is 1/16'' so ~1.59 mm and AC9 is 1.5 mm

my zatty is smaller than 1/16" so maybe its also a 1.5mm air hole

 

[tenshi]

my zatty is smaller than 1/16" so maybe its also a 1.5mm air hole

I have both, and ZAP is more airy than the AC9. Did they change it? I have an older version of ZAP.

Found this thread to that may help http://www.e-cigarette-forum.com/fo.../417152-z-atty-pro-airhole-wickhole-size.html

 

[dirquist]

I have a ZAP and an AC9 right here and regardless of the actual size of the hole there is no doubt that the ZAP is more airy than the AC9. Both are on the airy side, however.

 

[forg1vn]

doesn't zen have an open draw cap? i tried fitting a 1/16" drill bit into the hole and it was way too big, however i have a ZAU and not a ZAP but i don't think they'd have different caps would they?

 

[dirquist]

Zen has had a tight draw and open draw cap. He stopped with the tight draw a good while back. They are still around though. I thought but cant confirm that they all came standard with the open draw cap. Anyone know for certain?

 

[tenshi]

Zen has had a tight draw and open draw cap. He stopped with the tight draw a good while back. They are still around though. I thought but cant confirm that they all came standard with the open draw cap. Anyone know for certain?

I don't know either but would love to get a tight draw cap for an option. I looked around and email them but got no reply. I just got the 1.2mm cap for my AC9 and am hoping that Zen will release one for the ZAP again.

 

[cruxfm]

Thanks for the info. I only used a ZAP and pretty happy with airhole size but I have questioned how a tighter draw might vape.

 

[PEneoark]

I just got my AC9, but cannot wrap a non shorting coil to save my life. I'm not new to the genesis either. I tried with 30 and 28 wire.

Sent from my SGH-I747 using Tapatalk 2