Aga t2

[bfrie]

My life will never be the same. Just got my aga t2, made a super janky first setup, didn't even get close to fixing the hotspots. Thing measured 1.5 ohms, threw it on the evic at 11 watts. I csnt even imagine how amazing this thing will be when I learn to wrap a decent coil. Im absolutely blown away by how this thing vapes
Sent from my SPH-L710 using Tapatalk 2

 

[pillowking]

congra on never going back to cartos..
I have boxes of them just sitting here....

 

[bfrie]

Been off cartos since I got my t3 and protank

Sent from my SPH-L710 using Tapatalk 2

 

[pillowking]

I...... I can't figure out how to work a clearo.
bought boxes of t3 after hearing that they are much better than the cartos, just can't seem to get them to work right.
aga-t? 20 minutes and I had been in heaven since.

 

[MF DOOM]

I...... I can't figure out how to work a clearo.
bought boxes of t3 after hearing that they are much better than the cartos, just can't seem to get them to work right.
aga-t? 20 minutes and I had been in heaven since.

Oh come on man.

 

[SirSteve]

I went to clean my AGA T+ and the glass tank came out in three pieces, luckily I got the plastic tank with it also. Sadly I can't find the plastic tank, so now I have to wait for a replacement glass tank . But hey I got my Kanger T2 back in service, even with two hairline cracks it is not leaking, so clearos really do work!

 

[Telescope Neil]

Genesis RBAs on a mech are the best vapes I've ever had, so congrats on taking the leap into the world of gennies. If you're using an Evic, go mechanical and lower res, you'd be blown away again at how that setup vapes too. started on RBAs too with a regulated device, and that just rocked my vaping world. went SLR on a mechanical, then it happened to me again. Getting blown away twice with the same atty just shocked me, really amazing experience.

 

[eHuman]

bfrie, check out my blog. It should shorten up your learning curve on making a better aga-t set up.

 

[bfrie]

bfrie, check out my blog. It should shorten up your learning curve on making a better aga-t set up.

I'm going to just wing it for awhile to trybtov figure it out for myself

Sent from my SPH-L710 using Tapatalk 2

 

[Oktyabr]

bfrie, check out my blog. It should shorten up your learning curve on making a better aga-t set up.

Your posts have helped me quite a lot too! I've subscribed in fact.

What are your thoughts on the spring conversion for the AGA-T2? I found the tiniest compression spring my local hardware store had, clipped a short piece off, topped it with a tiny brass washer and replaced the middle nut on the positive post with it. Especially nice if I need to adjust the length of the top lead a bit but I wish I knew where to source an even smaller spring and washer. I haven't seen you write on this yet and wondered if you tried it and passed or???

 

[eHuman]

Your posts have helped me quite a lot too! I've subscribed in fact.

What are your thoughts on the spring conversion for the AGA-T2? I found the tiniest compression spring my local hardware store had, clipped a short piece off, topped it with a tiny brass washer and replaced the middle nut on the positive post with it. Especially nice if I need to adjust the length of the top lead a bit but I wish I knew where to source an even smaller spring and washer. I haven't seen you write on this yet and wondered if you tried it and passed or???

I wrote a short note on that once and what you describe is pretty close to the set up. I never got around to doing it as I can set up with stock gear pretty quick. I may set my wife's up with a spring so I can teach her to fish instead of always giving her fish.