yea it sounds like its really good.....now we need video to prove it wicks properly and wicks the tank dry...
- Status
yea it sounds like its really good.....now we need video to prove it wicks properly and wicks the tank dry...
I'd say that if you don't have a small lathe, then your going to need a lot of files.
The alum. caps (top and bottom) will be the tricky part. You'll be shooting for a leak proof seal between the top/bottom plug and the acrylic tank tube.
You will also need drilling and taps for cutting threads to what ever size screws that you use. But that is going to be the easy part. I have down to 3mm taps but if I need smaller they are cheap. And if I could only find a 7mm x .5 die I'd be happy(-er),,,,,, (yea you know where I'm going with that).
Edit:
I'm sure that there are ways to make a cap that seals that may not require machine shop skills. If your clever.
Thanks, I was figuring I would need a lathe... I may be able to get a machinist to do the work if I can give them specifics.
I can be clever but this would test that ability ten fold..lol..
I'm one of the readers that has not yet commented. you could say I'm speechless.
German engineering at it's best
German engineering at it's best
I commented earlier, but would like to say thank you for sharing your knowledge with us all. I live outside of Heidelberg and would love to check out your mods sometime when you return from your trip. Maybe I could do a little write up on here from an american's perspective of your mods. Thanks again and can't wait for part 2.
To all readers of this thread
Dear modders,
I am very pleased that you liked my mods and are taking part so vividly of my thread. This is part 1. Actually I wanted to just once give an overview of my work. In Part 2 I wanted to go into the details. Nevertheless, I am looking forward to your active participation. However, I am from Nov. 10th for about 3-4 weeks on vacation. After the vacation time we go into the "Canned."
One question I have: Who reads all this thread and has not yet spoken up? Just give me a short hello please!
Oh god, my english (but i try to learn it better from post to post)!
one more picture?
Hallo,
Deine "mods" sind absolute Klasse!!!!!!
Ich lese jeden post der hier geschrieben wird
Ich bin aus Bayern, eingewandert in der USA in 1974 und lebe in Northern Virginia, ausserhalb von Washington DCWillkommen in unserem USA Forum und Ich hoffe das Deine "Mods" uns hier in der USA aushelfen koennen, da die "normalen" Cartomizers etc. vielleich frueher oder spaeter hier verboten werden.
Ich hoffe das Du einen Klasse Urlaub hast and mit vielen neuen Ideen zurueck kommst
Karen
PS: Deutsch schreiben faellt mir nach so vielen Jahren in der USA ein bischen schwer, also mache Dir ueber Dein English keine Gedanken!
WOW, what a responce, i'm impressed! I couldn't believe having so much fans here
WOW! That schould work i believe.
And some more ideas for you:
Raidy - to continue from my last post. I realise the air tube doesn't have to go up the centre (and possibly spoil the capillary action of the mesh wick), it can go up the side. Also - the air tube is only necessary for vapers who like 'auto' batteries (like me
Do you think my modded E2 genesis would work? As shown on my new drawing...
WOW! That schould work i believe.
And some more ideas for you:
Last edited:
This is my DreamPipe. Never made a better one
This is a natural stone with neodym-magnets wiht hold and reload the pipe
The genisis atty
The finger-force infinitely steam regulation.
The microprossesor control unit
lot of wires to sold
The direct-finger sensors. It start with the last stored steam-value of the finger-force-sensor, which is allway stored in the control unit.
All about i need over 100 hours to build this. It was an incredible work that has me almost driven mad
This is a natural stone with neodym-magnets wiht hold and reload the pipe
The genisis atty
The finger-force infinitely steam regulation.
The microprossesor control unit
lot of wires to sold
The direct-finger sensors. It start with the last stored steam-value of the finger-force-sensor, which is allway stored in the control unit.
All about i need over 100 hours to build this. It was an incredible work that has me almost driven mad
WOW, what a responce, i'm impressed! I couldn't believe having so much fans here
you deserve it!!
also the italian forum is following this thread!
Raidy.... Your gonna have to start shipping them to us over here... I don't think you realize how well they will sell it's EXACTLY what most of us are looking for you should check out another thread on this site where all of us are trying to come up with the ultimate carto.... If u could incorporate the e2 cartomizer in this idea it might b possible for us "DIY'S" to make Something similar
Here's the link http://www.e-cigarette-forum.com/fo...kers-c-e2-r4-review-tips-info-help-video.html
I don't think you realize how well they will sell it's EXACTLY what most of us are looking for you should check out another thread on this site where all of us are trying to come up with the ultimate carto.... If u could incorporate the e2 cartomizer in this idea it might b possible for us "DIY'S" to make Something similar Here's the link http://www.e-cigarette-forum.com/fo...kers-c-e2-r4-review-tips-info-help-video.html
Raidy.... Your gonna have to start shipping them to us over here...
Here's the link http://www.e-cigarette-forum.com/fo...kers-c-e2-r4-review-tips-info-help-video.html
Like I always read the German forum. I'm a developer and modder, and it should stay this way. I do not produce and sell, never. I present my ideas for private use in the forums. And so it should stay. I have no financial interest in this development.
All my mods may be reproduced for non-commercial purposes.
Commercial reproduction is not allowed without my consent. I refer to the copyright.
I earned my money already There is enough money for the lawyer, in case it is building a illegal business!!
Last edited:
Ok well step by steps and videos if posssible would be greatly appreciated by everyone on this forum... You have a great talent.. Thank you for the info u have provided already ...and thanks in advance for future info
raidy - I read through this thread with MUCH interest and my jaw almost dropped in wonderment. I especially got a big kick out of your Bic lighter mod - LOL
Needless to say most of us don't have the know-how or equipment to build much of this stuff but just the Genesis atty alone using Kanthal and the steel mesh for wicking (oxidized as you have prescribed) hold much promise for those of us who are trying to mod the E2 R4 cartos. With the capillary action properties of the steel mesh working as well as you describe you really do have an auto-feeding juice tank mod. I think this might be very near the holy grail of vaping.
If one switches between various e-juice in the same mod do you have any suggestions as to minimize the taste of different juices or would you simply vape away whatever was in the mesh and it would be gradually replaced with the new juice with this type of capillary action in these meshes??
Needless to say most of us don't have the know-how or equipment to build much of this stuff but just the Genesis atty alone using Kanthal and the steel mesh for wicking (oxidized as you have prescribed) hold much promise for those of us who are trying to mod the E2 R4 cartos. With the capillary action properties of the steel mesh working as well as you describe you really do have an auto-feeding juice tank mod. I think this might be very near the holy grail of vaping.
If one switches between various e-juice in the same mod do you have any suggestions as to minimize the taste of different juices or would you simply vape away whatever was in the mesh and it would be gradually replaced with the new juice with this type of capillary action in these meshes??
Dear modders,
One question I have: Who reads all this thread and has not yet spoken up? Just give me a short hello please!
Raidy,
In just five days your thread had 235 replies but also was viewed 6603 times.
I don't want to throw in my uneducated voice but let seasoned modders do a discussion.
Don't worry - you have a huge crowd of followers.
raidy, your mods are simply stunning.
I can't believe how 'clean' and functional is your atom design.
just a question, do you do dryburns once in a while to keep the SS mesh unclogged?
I can't believe how 'clean' and functional is your atom design.
just a question, do you do dryburns once in a while to keep the SS mesh unclogged?
For e2 conversion: The original genisis atty has an air hole in the side of the vaping chamber of ~1.5mm size at the level of the coil, so you don't need an air tube (sorry slopes and auto batt users, this won't help).
Also, getting everything to fit in the e2 body will be harder as there isn't much room to work in. (raidy said several times that getting this smaller was quite difficult. On a plate of about 9.5mm, less actaully, you need 4 holes to mount of varying sizes. Ok, the filler port could be done elsewhere.
I was thinking of using a 1/2" pill fob from harbor freight, as in the suckaton, upside down with a mouthpiece added. This could eliminate the need for machining with a mill, and once built it wouldn't need to be opened. Dunno though.
Also, getting everything to fit in the e2 body will be harder as there isn't much room to work in. (raidy said several times that getting this smaller was quite difficult. On a plate of about 9.5mm, less actaully, you need 4 holes to mount of varying sizes. Ok, the filler port could be done elsewhere.
I was thinking of using a 1/2" pill fob from harbor freight, as in the suckaton, upside down with a mouthpiece added. This could eliminate the need for machining with a mill, and once built it wouldn't need to be opened. Dunno though.
- Status
Similar threads
- Locked
