anyone using syringe tank?

[ipjh89]

Any bros here uses a syringe tank mod? Bro karl like ''enlightened'' me to the wonderful world of diy... now i thinking everything also want to DIY...but pv mods still no idea how to go along on doing...lol

 

[Stinson]

Syring tank I use to use but after awhile,not good le.I would say it for fun but not for long,your heart will crave for more.

 

[ipjh89]

haha... i also make for fun de... to destress from my mountain of workload... more of a novelty than a functional peice of equipment

 

[MC28]

Lazy to DIY so i went to purchase a M1A1 Notcigs tank instead...Using it everyday with LT..

 

[ipjh89]

Bro MC28, check with you, when u refill ur m1a1, u just unscrew the thumb screw and fill right? does the juice leak out when u fill or when you screw the thumbscrew back? cuz i am doing a prototype with my syringe mod and it leaks when refilling...

 

[Stinson]

Maybe not tight enough?Or when you fill,let out a bit of air cause too much pressure inside sure will force juice out.

 

[Madshock]

Bro MC28, check with you, when u refill ur m1a1, u just unscrew the thumb screw and fill right? does the juice leak out when u fill or when you screw the thumbscrew back? cuz i am doing a prototype with my syringe mod and it leaks when refilling...

Im not sure about the M1A1. But if you are using the thumbscrew hole when refilling the tank... especially with punched cartos... CONFIRM WILL LEAK thru the carto end. To solve this, u have to block the 2 holes top and bottom of the carto and do your refilling... OR push the tank up so the hole is not within the tank ( hope this makes sense) but this defeats the M1A1 thumbscrew hole purpose.. well unless u using XL carto and the tank has room to slide to the top.

The leaking is simply because... the thumbscrew hole acts like a vent so the liquid will just flow thru into the carto. if u block the ends of the carto.. it minimizes the exchange of air pressure within the carto itself so the juice will not just flow thru, tho i dun think u cant prevent it 100% even with the holes blocked...

My

 

[MC28]

Bro MC28, check with you, when u refill ur m1a1, u just unscrew the thumb screw and fill right? does the juice leak out when u fill or when you screw the thumbscrew back? cuz i am doing a prototype with my syringe mod and it leaks when refilling...

Ya but nv leak before...If it helps, i'm using Boge XXL LR Cartos with it..

 

[barbosa]

lol i made 1 of these for the sake of making. but the rubber piece are somewhat arent tight.

 

[deathared]

Same here, I made one too. It slides up/down easily when you just bump it a little. Then if suay everything just leaks out. Thinking of getting the dct tank on HC, they just came out with the chrome ones. Looks damn nice! somemore, 2dollars for each prepunched dct. So I was thinking of getting a few 2.5ohms for my LT. Loving my LT, though just using the atomizers they provided by dripping. Works like a champ though.

 

[MC28]

Same here, I made one too. It slides up/down easily when you just bump it a little. Then if suay everything just leaks out. Thinking of getting the dct tank on HC, they just came out with the chrome ones. Looks damn nice! somemore, 2dollars for each prepunched dct. So I was thinking of getting a few 2.5ohms for my LT. Loving my LT, though just using the atomizers they provided by dripping. Works like a champ though.

My word of advise, dont use the flange dual coils which comes together with it..They leak like no tomorrow...I use it previously..

Get a box of Boge XXL LR Cartos to go along..Just have to punch ur own holes..

 

[barbosa]

the pre-punched hole dam tiny unless using very high pg or might risk getting the carto burnt

 

[ipjh89]

yup... the dct carto is known to have alot of problems... i using the boge 510D... like what they say: works like a boss!
but i still exploring the m1a1 idea... cuz will be easier to refill

 

[MC28]

yup... the dct carto is known to have alot of problems... i using the boge 510D... like what they say: works like a boss!
but i still exploring the m1a1 idea... cuz will be easier to refill

I think it has something to do with the material of the tube..

Recently i found out accidentally when i throw the whole tube into hot water to rinse it, notice that the material can be soften and bend when hot..Panic for a moment before i remove both the endcaps, dump it into hot water again and then overflowing the cup with cold water..The shape went back and a stain which i accidentally left on it is gone as well..

Anyway, i'm purchasing another 3.5ml DCT from smoktech to use..For the fun of it i guess..

 

[ipjh89]

Omg... So powerful.... But "unbreakable"... Should be plexiglass... But the melting point for that is very high leh.. And is more like acrylic than polycarbonate...hmm... Interesting...