I have taken the liberty of translating the Instruction manual for those who like these kind of things. Hope you will find it useful. You can view or download the PDF here.
[FONT=&]Menu system:[/FONT]
[FONT=&]The CVI has 7 menus.[/FONT]
[FONT=&]To use them, click the silver button using three rapid clicks.[/FONT]
[FONT=&]After 3 seconds, the screen will display "ANYVAPE" then blank screen, then "SETTING".[/FONT]
[FONT=&]Click the button once for each option, while "SETTING" is displayed, to scroll through the options. Stop on the option you wish to change. Wait 3 seconds, the current value is displayed. Then the values can be changed. Single clicks will step through the available values. Wait for the screen to go blank, the option will now be in effect.[/FONT]
[FONT=&]1. Voltage/Power UP.. single clicks will move the Voltage/Power up.[/FONT]
[FONT=&]2. Voltage/Power Down.. single clicks will move the Voltage/Power down.[/FONT]
[FONT=&]3. LOCK ATOMIZE : LOCK: On/OFF will scroll: [/FONT]
[FONT=&] Lock: On = Atomizer is OFF. [/FONT]
[FONT=&] Lock: Off = Atomizer is ON. [/FONT]
[FONT=&] NOTE:[/FONT]
[FONT=&] Use this feature in place of the 5 click on/off used on EGO's, Spinner's and most manual batteries.[/FONT]
[FONT=&]4. Batte[ry] Voltage: displays the remaining charge/voltage for the battery (a fully charged battery reads 4.1v-4.2v) Should be recharged by the time it gets to 2.5v.[/FONT]
[FONT=&]5. LCD Display: Set the LCD to display the information you would like to see when the device is in use; display Voltage/Power, resistance (of attached atomizer), or battery's voltage.[/FONT]
[FONT=&]6. LCD ON/OFF :Turn the LCD screen on/off while in use.[/FONT]
[FONT=&]7. V&P Model: (Voltage/Power) Switch to RMS volts or RMS watts output[/FONT]
[FONT=&] Voltage: as set (default=3v), [/FONT]
[FONT=&] Power: Variable Wattage as determined by the atomizer load[/FONT]
[FONT=&] NOTE:[/FONT]
[FONT=&] When switching between Voltage/Power, only Power(RMS Watts) is remembered. Each time you select "Voltage" or remove the batteries, the voltage goes back to 3v. What this means is that you can not switch between volts and watts to see the corresponding value. i.e. what volts are being used for a given wattage. But, the selected watts will remain even when the batteries are removed or switching between Voltage/Power modes, Even if you have changes the voltage.[/FONT]
[FONT=&]One button- click men system similar to the ZMAX[/FONT]
[FONT=&]Menu system:[/FONT]
[FONT=&]The CVI has 7 menus.[/FONT]
[FONT=&]To use them, click the silver button using three rapid clicks.[/FONT]
[FONT=&]After 3 seconds, the screen will display "ANYVAPE" then blank screen, then "SETTING".[/FONT]
[FONT=&]Click the button once for each option, while "SETTING" is displayed, to scroll through the options. Stop on the option you wish to change. Wait 3 seconds, the current value is displayed. Then the values can be changed. Single clicks will step through the available values. Wait for the screen to go blank, the option will now be in effect.[/FONT]
[FONT=&]1. Voltage/Power UP.. single clicks will move the Voltage/Power up.[/FONT]
[FONT=&]2. Voltage/Power Down.. single clicks will move the Voltage/Power down.[/FONT]
[FONT=&]3. LOCK ATOMIZE : LOCK: On/OFF will scroll: [/FONT]
[FONT=&] Lock: On = Atomizer is OFF. [/FONT]
[FONT=&] Lock: Off = Atomizer is ON. [/FONT]
[FONT=&] NOTE:[/FONT]
[FONT=&] Use this feature in place of the 5 click on/off used on EGO's, Spinner's and most manual batteries.[/FONT]
[FONT=&]4. Batte[ry] Voltage: displays the remaining charge/voltage for the battery (a fully charged battery reads 4.1v-4.2v) Should be recharged by the time it gets to 2.5v.[/FONT]
[FONT=&]5. LCD Display: Set the LCD to display the information you would like to see when the device is in use; display Voltage/Power, resistance (of attached atomizer), or battery's voltage.[/FONT]
[FONT=&]6. LCD ON/OFF :Turn the LCD screen on/off while in use.[/FONT]
[FONT=&]7. V&P Model: (Voltage/Power) Switch to RMS volts or RMS watts output[/FONT]
[FONT=&] Voltage: as set (default=3v), [/FONT]
[FONT=&] Power: Variable Wattage as determined by the atomizer load[/FONT]
[FONT=&] NOTE:[/FONT]
[FONT=&] When switching between Voltage/Power, only Power(RMS Watts) is remembered. Each time you select "Voltage" or remove the batteries, the voltage goes back to 3v. What this means is that you can not switch between volts and watts to see the corresponding value. i.e. what volts are being used for a given wattage. But, the selected watts will remain even when the batteries are removed or switching between Voltage/Power modes, Even if you have changes the voltage.[/FONT]
Last edited:
