Apex BF Customs

[McPuff]

A petri has done gotten an altitude adjustment.....

That looks so much better!!! Will you be offering then like tgat?

 

[McPuff]

That looks so much better!!! Will you be offering then like tgat?

Oh and how is the airflow on the petri?

 

[Roscoe01]

That looks so much better!!! Will you be offering then like tgat?

To be honest.....it took a good deal of work to squeeze that atty down that far. Was it worth the labor? Astheticly....yes! Performance wise....jury is still out? If I had a lathe at my disposal then it would be a no brainer!

 

[Roscoe01]

Oh and how is the airflow on the petri?

I must be lucky because the air is perfect for me. It has two 3mm holes so air is the same as an atomic wide open..... Slight resistance lung draw.

 

[bottomfeeder]

I have plenty of petri. I can set one aside for you if you like[emoji6]

What is the ideal ohm range for this guy? I tend to be on the higher side.

 

[Roscoe01]

What is the ideal ohm range for this guy? I tend to be on the higher side.

Everyone likes a different vape but I would say with larger chamber size and fixed air one would probably want to build sub .5ohm for a warm vape. If you like a cooler vape though one could build higher.

 

[Roscoe01]

I guess I'm happy to be able to use all my tools again just revisited the buhawi and I decided to open up the air a bit. Much more betererer!

 

[McPuff]

I guess I'm happy to be able to use all my tools again just revisited the buhawi and I decided to open up the air a bit. Much more betererer!

Is it a pain? Could you do mine if I send it in?

 

[Roscoe01]

Is it a pain? Could you do mine if I send it in?

I sure could but...i am exceeding the tolerance of what should be drilled in that area which weakens the top cap nipples considerably. Glad to do it as long as u keep that in mind.

 

[McPuff]

I sure could but...i am exceeding the tolerance of what should be drilled in that area which weakens the top cap nipples considerably. Glad to do it as long as u keep that in mind.

Awesome. Im gonna send you out a package this week.

 

[Papa_Lazarou]

which weakens the top cap nipples considerably.

Wait... what, now?

 

[Roscoe01]

Wait... what, now?

[emoji16]

 

[RiverNut]

Any idea how to chop a pyrex glass Ross?

maybe a glass tube cutter?

 

[Subohmies]

maybe a glass tube cutter?

Tried but not working

 

[Roscoe01]

I have added reo bullet button covers to the site. Will also be adding tiger wire today as well.

 

[RiverNut]

Once you get your groove back you should put Avion on the site too

 

[Roscoe01]

Anybody interested in the evil monk rda?

 

[mommabird62]

I have added reo bullet button covers to the site. Will also be adding tiger wire today as well.

Sweet! I love that tiger wire that I got from you! Still need to build something with the crazy wire. It takes an atty with big holes! LOL


Sent from my iPhone using Tapatalk with my paws

Mommabird62

 

[RobbieVape]

I like the evil monk could be a challenge as no well, wondering about leaks. Apex JR thought on other hand would be worth a shot, may need to slot for bf due to low middle pin but super reduced chamber - lower than derringer


Sent from my iPhone using Tapatalk

 

[Roscoe01]

I like the evil monk could be a challenge as no well, wondering about leaks. Apex JR thought on other hand would be worth a shot, may need to slot for bf due to low middle pin but super reduced chamber - lower than derringer


Sent from my iPhone using Tapatalk

I watched a couple reviews of the evil monk this am and surprisingly enough very little leaking reported by the reviewers......go figure.